Honda XRV Forum banner

arm

  1. Fuel overflow lines - where to connect?

    Africa Twin
    Hi everyone! I recently remove the tank, airbox and carburators to change the main jets after changing to a more open exhaust. Know putting everything back I have a small problem... There is several fuel overflow or drain lines connected together to one main line that dumps excess fuel it...
  2. SLR, FX, FMX Swing-Arm

    Dominator / FMX
    I’m pretty sure all the above use the same basic frame, so the dimensions i’m after should be the same. Could someone with a Swing-Arm from one of these measure the front pivot width. That would be the outer width, i.e. the width required in the frame and also the inside width, i.e. the width...
  3. swing arm swap

    Transalp
    Does anyone know if i could fit a aluminium swing arm from an Africa Twin, onto my TA700, as i have fitted a decat pipe !!
  4. Honda xl breather hose??

    XL
    1976 honda xl 250 breather hose is in a "T" ...comes out of the crankcase,then T,s off hanging down by the swing arm,then the upper part that T,s off goes towards the front of the bike and i cant figure out where it attaches to it dont go on the air box or anything..does it just hang up somewhere??
  5. Chain length AT swing arm on XL600 v

    Transalp
    Hi i was just wondering if anyone knew what length chain i would put on my Re-build. I have put an AT swingers onto an 87 Transalp frame, I think the AT had a longer chain than the TA due to the longer swingarm but no sure about this combo...
  6. Frame blanking plugs

    Africa Twin
    Just a little tip if your looking for a new cap for the swing arm bolt i found these work great. Just had to cut about 6mm off the length for it to fit flush...
  7. Swing-Arm dimensions

    Dominator / FMX
    Does anyone have a Dominator frame and/or swing-arm handy that they could measure for me? I need to know the width across the front of the S/A i.e. along the pivot (or the width inside the frame where the S/A fits).I also would like to know the S/A length, i.e. from pivot to wheel axle (middle...
  8. Is this beyond repair? Swing arm

    Dominator / FMX
    I think I know the answer :(
  9. Tools needed to stirp TA

    Transalp
    Hi All, I'm doing a quick trip to Brisbane to pick up a doner Trans Alp and need to pull front end and swing arm / rear wheel off to fit on a pallet for shipping to Darwin. I will be cutting the frame to fit it on as the frame is bent and i have a spare. Just after some info on what tools i may...
  10. Swing arm bearings

    Dominator / FMX
    Hi. Can anyone point me in the right direction to find a replacement set of swing arm bearings to the Honda FMX. Genuine Honda one seem to be discontinued and are very very expensive. Are there any pattern parts out there ? Thanks. Jez
  11. For Sale: Various New Old Stock RD03 & RD04 Swing Arm Bearings and Seals

    For Sale / Wanted
    I have a selection of new bearings left over that are no longer of use to me: - 91071-KS6-004 x4 Swing Arm Needle Bearing 52141-MM9-000 x2 Swing Arm Bearing 52473-MS8-000 x2 Rear shock linkage Bearing 52144-KR8-005 x2 Swing Arm Dust Seals 91254-KS6-003 x1 Dust Seal 52109-MM9-300 x2 Swing...
  12. NX650 Bearing Part Number

    Dominator / FMX
    On the off chance, does anyone have a list of bearings required to rebuild a 2000 nx650 (not engine internals). Wheels, Swing Arm, Linkage etc As a lot of people have rebuilt theirs, thought they may have a list lying around with this info on.
  13. SLR Rear shock recommendations

    Dominator / FMX
    I am looking to replace trhe rear shock on my 1999 SLR and am wondering what my options are without it costing an arm & a leg?? Thanks in advance Tom
  14. Ethanol (and the Arm-chair-biker) !

    Transalp
    From armchairbiker.com Ethanol in petrol. The what 'Classic' riding motorcyclists need to know. Share & Enjoy !
  15. Fork help from accross the pond

    Africa Twin
    Hi all, First post from across the pond, what a great board. I wish we had AT in the states. I mean old school AT that is. I have a 1989 TA that has 11k on the clock. I love the old school bikes, reminds me of my younger day:) So I'm doing the AT RD03 swing arm swap so I can have disc brakes. I...
  16. A question re rear suspension link 650

    Transalp
    can anyone tell me the correct way up for the forked arm on the rear suspension of a 650 tranny. mine is fitted with the lower shock absorber mounting lug being lower than the pivot point but this photograph shows it the other way up ie with the shock mounting above the pivot
  17. 600 centre stand question...

    Transalp
    Hi folks....I managed to track down an original centre stand for my TA. It's in pretty good shape. I've not fitted it yet, but I've a question for anyone in the know: on the microfiche parts pic, along with the stand & springs etc. it shows an additional 'arm' and a couple of 'clips'...I'm...
  18. Dirtquake

    Chatter
    Had a great weekend at Dirtquake which takes place at the Adrian Flux arena in Kings Lynn, loads of nutters on everything from scooters to 1100 sports bikes and choppers racing around a speedway track, few serious racers having a go too , Guy Martin, Carl Foggarty, Steve Plater, Gary Johnston...
  19. Honda Engine XR125/200?

    XR
    Hi, I brought a basket case from a police auction sold as a Honda XR. So with it being from a police auction there are no identity marks on the frame or engine I have attached a few pictures of the engine in the hope that someone will be able to tell me if it is in deed a XR engine. I have...
  20. Shock link

    Transalp
    Has anybody found an aftermarket supplier for the needle roller bearings on the 650 shock link, I only want the two where the long link attaches to the swing arm but at Honda prices just over £30 each they are a bit dear! Iv'e found the same size bearing at bearing shops BUT they are the caged...
Top