Anyone know where I can get a set of bolts and screws for my fairing?
'87 Transalp 600 with original fairing?
I have found this one online, but not sure it will fit my early bike?
Genuine Honda large top box.white with blue centre (easy to paint to match you bike)
Backrest pad,two keys and has mounting plate and all bolts.
Was fitted to my 700 T.alp.Would fit many other models. £70
Based Wirral CH42. Cheers Dave
During our move a box has been misplaced :(
Now I have time, space and money to start this rebuild.
A lot of xrv rd04 have been broken for parts but no one seams to keep the little things !
Pricing these small items new, very expensive.
Had a bit of a nightmare yesterday after installing new pistons reassembling the heads and getting the engine back in the frame quite nicely disaster struck. When torquing down the small 6mm bolt in the cylinder head it snapped like a bit of cheese. As usual this was the last bolt.
To fit a...
Brackets for auxiliary fan are back in stock.
You can now run two fans. Ideal for sand and mud riding in hot climate.
You can spot weld them or use a special aluminum glue.
50$ cad a set. Includes bolts.
Only 20 sets available.
Hi,Can anyone recommend a good foot stand extension plate for the XL700?I've had a Cameltoe fitted for a couple of year and although it looked good I was not impressed with the way it bent with use and the bolts were continually working loose. So loose in fact that it now lies somewhere along...
Was doing a routine check and found that the front axle holder was broken and the nuts on the studs were so loose that they could come off by hand.
Anyway as I do not have torque wrench I managed to snap 1 stud off and then was trying to put a temporary support plate which caused the other stud...
First big problem on my rd03 restoration the casting on the hub broke away when removing the very stuck bolts. I was going to rebuild the wheels anyway.
So I need
Or transalp 600 hub Or wheel
Or dose any one know of any other wheels fit.
Sent from my SM-G955F using Tapatalk
I am using this site to try and order some bolts that I require to put the original backend on the bike
question I have is this, to order the bolts for the carrier(I have the collars) it shows bolt number 27 for the middle...
I have bought a 97 RD07a and there is an aftermarker rear end on it. I want to put the original back on so I can have a top box. Problem being that I dont have the bolts for the rear mudguard and rear carrier. I have checked online but its nearly 80 quid for replacement ones. Does anyone have...
Finally got round to fitting the different front wheel and forks. So have a single disc wavy disc. I believe its a Sumo disc. with the bolts. and new pads with less than 300 miles, fitted for mot. Will be marked inside and outside, so pre run in.
£30. plus postage.
This bike is in better than showroom condition. I have stripped off any corroded parts and powder coated them. Also, changed most bolts with stainless steel, where permissible. Almost new tyres, new battery, re-spoked rear wheel, full service. Centre stand, 2 keys and owners manual. It runs and...
Hello troops thanks for the previous help much appreciated, now I'm wondering is the front sprocket meant to have some play in it, and what is the correct way round please im guessing the flat side has the retaining clamp as the way I found it other day it had the ridge facing out with the clamp...
It's been a while since I posted as I've had a difficult year emotionally etc, but alas, I have a question of an XR400 nature.
I sprayed my valve cover earlier in the year and renewed the copper washers on the rocker pivot bolts as I had an oil weep, and when refitting, I used a new...
I recently bought a set of secondhand GIVI Outback pannier frames that were in a poor state due to off-road use.
So I stripped the powdercoating and got them re-coated in a bright silver (work done by Micro Fusion in Bedford)
The alloy catches at the top were restored with alloy wheel paint and...
Putting casing back on after blasting + powder coating. Kept all bolts in position through a piece of cardboard. One of the 3 long bolts that holds the outside cover of the stater / pick-up cover on has a copper washer on it. I cannot remember putting it on the bolt, but must have done !! Does...
Does anyone know what size bolts are used, to attach handlebar mounts to the triple clamps.
Im looking to buy new mounts, I measured the length of bolt but didnt check bolt diameter, and looking on net, some use M12 bolts but some use M10