Search Results for ‘bottom’

Anyone taken the oil strainer out of the bottom of their frame? Tried removing it yesterday, so i could check it, and get frame ready for powder coat, but could not get it to undo. Tried interlocking two spanners to get a higher torque, but still no joy. Any tips on removal???

i have this and it seems a shame to bin it genuine 600 exhaust muffler/silencer the 'bottom' end is is perfect nick, but there is rust and a 8mm hole on the rear - easy fix for someone who can weld or rivet a plate on top? collect north London or £10 postage (uk)

Hello co-africans i have a problem. When mybike is on neutral and only on neutral and only when its cold and I pull the throttle I hear a clicking noise coming from the bottom right of the engine It stops after 10 minutes when the bike is better warmed. Should i worry cause i am frightened as a...

Does anyone have the torque settings for the bottom linkage bolts, below rear shocker, for the above, please. All I can find in my workshop manual is ' tighten the bolts securely '. ??

Does any one have one of these for an RDO4 please ? the one i fitted for an RD07 is causing me a few problems. it fits on the bottom of the rear shock Also im after one of those stickers below for the front or know where i can get one please.

Wanted RD04 3 way bottom rear shock pivot mount, put a RD07 one on and it lifted the back end which is ok but the center stand now knocks on it so i think i might put the correct one on it.

Hi Guys i'm having trouble splitting the bottom engine case on my 82 Xl500r, i have to replace the kick start return spring, i have the engine upside down on the head & I've removed all the exterior screws, are there any internal screws i have to remove & what is the best way to separate them...

Hi again. At the bottom of the V on the right side of my XRV650's engine is a bolt, that will not tighten, what is it for? As usual, the bloody manual doesn't mention it...

I have damaged the left hand fork slider (bottom at the thread where the spindle screws in). I can get second hand ones from ebay but they are from the single disk model. Now, the single disk model has the disk on the l/h/s, good, I obviously need the mounts for the calliper, but are they the...

I have snapped my throttle stop screw on my Dommie it would appear they are made of unobtainable steel. NLA I am informed by my usual parts provider. My hope is someone can suggest a replacement. I have seen other types of tss's but am unsure of what to go for. Any suggestions ? Have you got...

Sorry for the silly question this double spacer , the big part should be on the bottom of the windshield or the top ? i put the big part on the bottom but i feel it's wrong as there is a big hole that the small part can get out through when you have a lot of vibration. can anyone check his/her...

How the hell do i remove the clear plastic circle in the bottom of the master cylinder to check to see if my return hole is blocked??? Many thanks in advance Dave

Hi I am looking for an post 1996 XR 250 BAJA ,maybe even just an engine or bottom end . What is out there ?. Thanks

In comparison to gold, this could be legal tender.https://www.dropbox.com/s/gnoufv43jsc1rq2/2015-12-12%2012.52.00.jpg?dl=0 It's more expensive, at £2.75 each.:mad: Honda are ridiculous for their prices for small items. They wanted £2.80 for one the tiny copper washer at the bottom of the front...

hi im after a camshaft for a 1983 xl250rc, must have the pin to drive rpm tacho or atleast the hole to put in my own pin. i have lots of spares and 2 working bottom ends with numbers electrics etc etc. contact me cheers ken

I've riden lots of bikes in the past & most have had centre stands, but the one on my RD07A has beaten me! My last bike was a Vstrom & that seemed to have a short piece sticking out at the bottom... apply weight & up it went. But on the AT there is no bit sticking out & no amount of heaving...

Howzit from South Africa! The bottom half of my chain slider has broken off, and finding body parts here is a bit of a task. Has anyone replaced theirs with an aftermarket model or another Honda model, and if so any advice? Thanks inmates!

Has anyone come up with a way to stop the sidepanels coming undone from the bottom rubber mounting and flapping open at speed?

On the XR650 forums they talk of cleaning the oil strainer in the bottom of the frame tank. I can't see any mention of it on the microfiche - is there one on the vigor / SLR?

Hi I had the seals replaced on my xr yesterday. I put front end back together pumped the forks up and down - and fork oil squirted out of the bottom of the RH leg - from the big hex socket cover. It's up on the stand now and is not leaking when not under compression. Suggestions?