Hello everyone !
Does anyone have a good reference for a new carburetor maintaince kit with new joints/Jets ect for a transalp 600 1998 ?
I was looking at buying the orginal kit at honda but it seems super expensive , Ive seen some aftermarket kits for half the price but i'm not sure if the...
My 600 (1987) developed a flat spot this afterrnoon, around 4,500 revs she bogs down momentarily before picking up again.
It feels like fuel starvation, except that she'll then shoot round to the red line with no problem.
So, given that 90% of carburetor problems turn out to be electrical...
Hello there! I was rebuilding my carbs while looking at the Honda fiches, and saw that a gasket on my carb is positioned differently. On the fiches, the order is: 28-1-15, so the metal collar (15) sits on the carb, the gasket (1) sits on the metal collar, and the plastic plate (28) sits on the...
I'm struggling (failing) to find throttle slides for RD04 anywhere, anyone know. Do i have to search for it using any particular measurements? not finding anything when searching for slides for RD04!? does the RD07's fit?
Also looking for a main jet needle.
Appreciate the help
For a 74 xl350e any experience or suggestion on which carb to use I am having a hard time locating exactly which carb to use. There seems to be a few variations of the mikuni vm38 and the 38 mm one from kelhin I don't need to use the original choke cable. I just can't afford the 200-300 original...
NX650 from 1988.
Have a jet kit in the mail and planning on doing Dave's mod.
I wanted to take the carburetor apart and clean it up before hand, but having trouble getting two of the screws in the float chamber out - seem very soft and I don't want to ruin them.
I have PH and PZ...
Anyone know where I can get a carb rebuild kit in the uk for my xl650?
Something like this
HONDA XL600V TRANSALP 600 NEW KEYSTER CARBURETOR MASTER REPAIR KIT KH-1347 | eBay
would be perfect. 600 ones seem common, but not 650. Not sure if there is significant difference, but 650 models...
I have some troubles with my fuel lines on my RD04.
Wich INNER diameter should I use?
it seems the tank outpunt diameter is not the same as the input/output for the fuel pump and the inlet for the carburetor.
what diameter of tube should I use. I had never problems fitting those, but with...
I am a complete newbie to motorcycling and I am looking for help.
I have been given a Honda xr 125 with electric start, I have now sourced a carburetor which was missing and a battery.
The problem is I have a rats nest of wiring and I don't have a clue where to start, the few wiring...
Anyone managed to find a source for the diaphragm in the air cut off valve (just above throttle cable on right of carb)
I have a slightly damaged one and baulking at the £110 Honda want for one
Part #9 on Genuine Honda Parts | Honda Cars | Honda Motorcycles | Honda Power Products | Lings Honda...
Hello, im new to the forum and had a question about a bike i started rebuilding, the bike is a XL500 R Paris-dakar edition (1983 i think?) when i got the bike it was in regular condition, not running as some parts where missing, unluckily the carburetor is one of them. After checking around the...
Going to try and replace my carbs on my AT due to broken and lodged choke plunger on left side but no luck with ebay except for ones for a '90 and a 2001 model. Anyone know if either of those are the same as a '97 or know where I might source one?
thx for any insight.
I just found out I might have swapped these so need confirmation on marks on front and rear needle.
Only info I found in this thread http://www.xrv.org.uk/forums/africa-twin/78824-rd04-original-carburetor-needle-size.html
so would like another confirmation if possible. It says in the thread...
I've ordered some alternative main jets for altitude. In the XR400 Haynes manual it says the main jet can be removed via the drain plug on the float bowl. Honda don't supply whatever type spanner is used for this, does anybody know what size and type of spanner fits?
Following a liitle mis hap while sorting my carb out (dropped the bloody slide and bent the needle) I needed a new needle<br><br>NRP Carbs in Manchester sorted me out, they are doing a full carb kit cheaper than a new needle would be.
Top guys who can sort different jets etc should you...