Honda XRV Forum banner

clamps

  1. Standard carb clamp sizes

    Dominator / FMX
    Sorry folks, I'm asking for help again. I'm going to hopefully be cleaning and stripping the carb this weekend and while its out i will be replacing parts as i go. Does anyone know the sizes of the carb manifold clamps for both the air filter and inlet manifold rubbers? I would try and...
  2. Alternative Facet fuel pump

    Africa Twin
    Question for the gurus please. I found this Facet pump: "Facet FEP04SV Posi-flo Electric Fuel Pump 1.5-4 Psi Includes Clamps fittings" The psi is 1.5-4 and flow is 25Gph. Will ot work as a replacement to the oem pump?
  3. Crf450 forks on an XR400

    XR
    Has anyone e done this modification. I like the thought of USD forks. I know I'd need the triple clamps as well but would love to know if anyone has done this mod? Ben Sent from my SM-G930F using Tapatalk
  4. Dommie Handle Bar mounts

    Dominator / FMX
    Does anyone know what size bolts are used, to attach handlebar mounts to the triple clamps. Im looking to buy new mounts, I measured the length of bolt but didnt check bolt diameter, and looking on net, some use M12 bolts but some use M10
  5. How to remove fuse box terminal

    Africa Twin
    My headlights stopped working because a wire came loose from the back of the fusebox.(see pic) Probably I can simply stick the wire back where it came from and squeeze the metal clamps tight again. As you can see on the pic the clamps (where the wire should be fitted) are visible in the...
  6. Just another dumb question.

    Dominator / FMX
    Before I go spending £30 plus postage on a braided hose for my rear brake, I was wondering if I could use the piece of braided rubber oil pipe that was left over from fixing the line from my oil tank to the cylinder head to replace the hose from the rear brake resevoir to the master cylinder...
  7. Fork Gaiter Clamps

    Africa Twin
    Bought a new pair of gaiters for the RD04 and just checked the price on the gaiter clamps / clips - £11:83 each!!! That's £47.82 for what are effectively 4 thin jubilee clips, for goodness sake. Needless to say, I shall be looking for alternatives.
  8. XR400 - Holding Flywheel Whilst undoing bolt

    XR
    Hi all, I am trying to remove the flywheel and having problems stopping the flywheel spinning whilst removing the flywhell bolt. The motor is out of the frame for a crank swap. I have a pair of the long molegrip type clamps that can be used to remove the clutch or flywheel and am locating the...
  9. Removing carbs on 600...? Stuck

    Transalp
    Hi! Trying to remove the carbs on my 96 600 TA and it's not easy..... I have disconnected all the cables and tubes and unscrewd the clamps. I just get a small play when trying to pull it up.......Anyone removed the carbs and can come With som Magic advice? Thanks
  10. Wemoto carb rubbers

    Africa Twin
    Anyone used these? With the cylinder head locating tab in the correct postion they don't seem to allow the clamp/clip with the tab to line up properly. It ends up fouling on the valve cover and slanting diagonally across the rubber. There are two different clamps and I have them installed the...
  11. For Sale: Bar risers Touratech XChallenge, XCountry, Xmoto

    For Sale / Wanted
    Bar risers Touratech XChallenge, XCountry, Xmoto Removed from XChallenge as I now have different WP forks/clamps. 20mm bar risers. In the TT catalogue they’re £25 plus shipping and allegedly take 10 to 14 days. This usually means 10 to 14 months. 20 mm handlebar riser BMW G 650 X...
  12. For Sale: Honda XR complete USD Front End

    For Sale / Wanted
    Yamaha WR 450 front end been modified to fit Honda XR, complete new stem machined has bottom bearing fitted. If I remember right the forks and clamps are 02/03 the front wheel is 05, all new bushes and seals fitted when I did the conversion and only run on the bike for a few months before I...
  13. Triple clamps hitting IMS tank on full lock.

    XR
    I don't know if any of you guys have an IMS tank fitted or experienced the above, if you have heres a solution. IMS Tank being hit by clamps I'd asked the question over on ADV, but despite the advice given I.E. try adjusting the hardware, make sure that the tank sits onto the spine correctly...
  14. chroming header clamps or other finishing options ?

    Dominator / FMX
    one part of the dommie that looks crusty after a while are the header clamps . Just wondered what people think of various finishing options eg chroming /galvanising etc. thanks Bill
  15. Reducing handlebar buzz on a big single ?

    Dominator / FMX
    Ok it's not much on the dommie with it's rubber mounted bar clamps but I love spoiling my steed and wondered whether gel/foam or multiple density grips would help Also bar-end weights ...worth it ? Anyone had experience in bringing the finger tingle to a minimum on long rides? thanks Bill
  16. WTB transalp 600 lifting handle (grab handle for centerstand use)

    Transalp
    It's an obscure part but it bolted to the left rear footpeg perch and frame. It consists of a handle and a pair of clamps. The idea is this handle will help you hoist your TA onto its centerstand. I think the handle was the same for all 600cc bikes. The handle part number is 5025-MS6-620ZA...
  17. Sold: Africa Twin 07 front forks, yolks and bar clamps.

    For Sale / Wanted
    Having a bit of a clear out and found these tucked away, they came off the donor bike for Insomnia, complete top yolks, steering stem etc plus the bar clamps with original bolts and the fork legs. Straight and true, no impact damage and no leaks from the seals. Asking £75 plus postage at cost.
  18. exhaust pipe flexi tube

    Dominator / FMX
    Flexi exhaust pipe tubing FLEXI EXHAUST PIPE TUBE WITH A PAIR OF CLAMPS SIZES 51mm. 54mm. 57mm AND 60mm. | eBay Your thoughts on this I have seen this advertised and thought could I should I try this product.? I am trying to connect(on my Dommie flattraker project) a xl header pipe to Honda...
  19. anyone ever chromed their header clamps ? will it last?

    Dominator / FMX
    Always noticed how rough the header clamps look on my Dommie and wondered if I grind them back and send for chroming whether they'd be likely to look decent for a reasonable length of time ...or is the temperature just too high to allow any finish apart from stainless to last? your advice...
  20. Question - How much to raise the rear end

    Africa Twin
    OK, I have figure out what the height differance between new front end and old one is. just by pushing forks through clamps and getting faily rough idea i think the forksa are 1.5 inch longer. So if front is 1.5 taller how much do i raise the rear? Seen as shock is angled and is on a...
Top