Anybody fitted some ??
I tried to fit some today and failed
All bolted up and connected to the existing colour coded bullet connectors in the loom
Relay already in place and switchgear present & working
Fired up the bike, both rear indicators worked when...
I am ordering some connectors to renew and modify parts of the wiring loom on my 1988 RD03, but I can not seem to find connectors for the CDI. Does anyone have a reasonably priced lead on these?
Also, I am at work in Scotland right now, so I can't look at the wires for my self, but from the...
The last owner bodged the connection to one of the CDI units (1st image) and it is starting to cause a problem, I might change the CDI and I would like to get some waterproof connectors like the original ones (2nd image), does anyone know what these are called or where I can buy them?
i have a spare loom which i am mending some broken connectors
there is a 2 pin connector green in colour with 2 wires situated midway under the petrol tank the wires are pink and black
I have no idea what year dommie the loom came from
i am hoping they connect to the later carb with the...
I started the long awaited complete strip down of my 87 TA the other day and noticed a switch mounted under the rear mudguard. It is attached to an orange relay(?) with 6 connectors (only 2 of which are used).
Any idea what it is?
not sure if this is the correct area or not. I am about to receive a Mosfet reg, it would seem the only place to buy new connectors is the US. ???, is there any where in the UK that I can buy these?
Looking for a few suggestions before I make a start.
2008 Varadero 20,000 owned from new. Went to it today after standing for a couple of months, been on the optimate on and off for a few weeks, but always get the yellow 'fault' light at the end of the cycle. Turned the key, the fi...
Purchased in error!
Brand new Shindengen FH012AA MOSFET Reg/Rec
In line splash proof maxi-fuse holder & 30A fuse
10AWG black/red cables to go to battery
12AWG yellow cables to go to alternator
And all crimps to suit (or use your own connectors or soldered joints as you wish)
I'm looking to rewire/route the electrics too this block as its a known trouble spot.
Does the main battery feed also supply the spade connectors in this block in some way? I thought I saw a thread related too this subject on here at some point.
Lecy stuff is not my bag and need a idiots guide...
When stripping out the underseat tray I separated the square(ish) connector on the regulator and found the connections to be burnt looking!
Should I be worried about this? Should I replace the connectors and if so where from? Help anyone?
Sent from my iPhone using Tapatalk
I'm not sure how much difference a higher CCA makes to starting an AT, I've rinsed two Motobatts's in two years but then I've been refurbing and swapping out old for new parts and connectors along the way so I might have re-fried my second Motobatt by running it for a couple of months with a...
Hello again.. Cleaning up a second Dommie, and discovered that the reg rec was not working. (Confirmed by swapping out the reg rec from my daily ride) Ordered a new one (aftermarket), and when it came to put it in, noticed an extra wire coming out of the reg rec - black.. The original reg...
I am in the slow process of a complete rebuild and looking for some help.
I found a new harness on eBay and was able to get some used Speedo and Tach assemblies from Hamart.
It appears as though the wiring is incompatible as the wiring connectors are both male.... Anyone have any advice?
Not a new thread, I just want confirmation from experience: Can I use a post 2005 Yamaha R1's 50Amp Regulator/Rectifier for my 2001 AT? If so, does it need heavy modifications to the connectors and fitment?
The at wouldn't go yester day so being a bit chilly -2c I put the battery on charge. no it wasn't the battery. so checked the connectors.no not them. then the wiring no that was not it then the starter selonode no that's clicking away so out came the starter(after the exaust&bellypan came off)...
copied from an old thread on here
The seven wires on the RD07 loom are actually only five...
"The green ones and red ones are doubled up. If you look at a wiring diagram, the red ones are connected together in the loom and the green ones are also connected together in the loom. When...