Transalp 600 & XRV750 rear lift link SOLD
(Lift handle, silencer sold)
Transalp XL600V 88-94 & XRV750 RD03/4 Extended Rear Shock link for raised ride height.
I removed this lengthened link from a friends 1992 Transalp 600 as it was too tall for him. I now have that Transalp myself as he was...
Started to change the output shaft on my 700 XL.
All the bolts holding the chrome heat shields and the painted heat shields were sized in so that took me around 4 hours to do,
I’m a slow worker, drill out re-tap the holes and order new bolts.
The rest went as I expected it to no real drama...
My ‘93 Transalp 600 was putting out 16 volts when I bought it a few months ago, and had had some meltdown in the distant last. It had an Electrexworld reg/rec on it.
This morning I fitted a brand new aftermarket reg/rec to it. Wired it up, mounted it on a nice alloy heat sink plate of my own...
Please would somebody tell me if the four silver fixings you can see that hold the wind shield to the headlamp cowl are the correct ones for a 1999 XL600V?
Please see pictures.
They came with the bike when I bought it new but seem too big and shiny?
I guess this is my first post here. I hope to post more.
I have bought an FMX 650 2006.
There are no stickers on it, except one on front fender, and one on right gas tank side, but they are not original.
I was wondering, is there any electronic version of stickers, whether they are...
Im just about to start wiring my dommie project.
I have created a wiring diagram, and was hoping someone could give it a quick look over and give me feedback on any mistakes.
Also thought it may be handy for other people to use, (if its correct)
Can anyone advise how i can go about repairing an RD04 fuel level sensor as per the type in the image.
Is there a link available to buy the correct thermistor? I have seen the repair videos but seems this type is different?
So just bought it its silver/black 2005 abs 22k on it,i have fitted a new front tyre(metzler tourance) have bought a new chain and sprockets and my question is,does anyone know the correct torque settings for the front sprocket and the nuts for the rear sprocket,i live in londonderry n.ireland...
I have some evil thoughts about cutting in half the rebound spring or even more - ordering custom ones to be made if all is OK with the shorter length.
I am talking about part number 10 here
Now this is because I have good sag set up now, but when I put fork emulators they will...
Im new the forum and require urgent help.
I need to source a crankshaft for my XRV750 as far as I know the RD04 and the RD07 uses the same Crank is this correct.
For some unknown reason mine broke 3 teeth on the Timing Gear.
Im leaving a a long distance tour in 3 weeks and just my...
I have a 99' fx650 which I purchased to refurb and modify. I do not know how it ran before it was dismantled. It was only started.
I have now rebuilt after refurb and I'm having trouble with engine hesitation with throttle open.
I have put a larger main jet (175) as it has a custom...
Having trouble with a weak spark on my Honda XL250R. We think the source coil is at fault but on test it gives 76 Ohms resistance. The correct resistance is unclear as the manual we have says reading should be in the range 200 to 500 Ohms. However later it says that for post 1981 the reading the...
Ok so over the last 4 years and 30k this time of year the old girl runs about 55-65 degree according to me RR KATO digi temp sensor to the point were i cover the rads up to get it to around 80 in winter.
Now all of a sudden it upto 80-90 degrees with nothing covering the rads :???:
does anyone know or tell me where i could find the correct torque settings,the ones i need are as follows,the oil filter housing bolts,sump bung bolts(on frame and at the bottem),rear wheel axle,front wheel station,fork yokes and also the two allen key bolts on the head the ones that would be...
Has any one got a pilot jet for a carb fitted to a RD02 to hand, or happen to know the length?
Just stripping the carb and the current pilot jet that was fitted is 24mm in long, however the refurb kit for the carb came with one that was 28mm long. Any clues on which one is correct? The 24mm...