Honda XRV Forum banner

cylinder

  1. Transalp
    Has anyone else had this happen , when warming up the bike to change the oil , the engine hesitated then stall the temperature was 76 degrees, when i tried to restart the , the engine would only run on 1 cylinder but not tickover i kept it running with the throttle, can anyone help Neil
  2. Transalp
    Hi, Please would somebody give me an advice on changing the exhaust downpipes? I'm always worried I may shear off the lugs that screw into the cylinder heads when I'm undoing the domed nuts holding the flanges. Also, is there a work around to not having the gasket between the downpipe and the...
  3. Dominator / FMX
    Anybody know do the replacement cylinder sleeves (100.00mm) exist for Dommy and who sells that? Thanx
  4. Transalp
    I've just been checking the valve clearances on my XL700 and I've hit an issue. The rear cylinder was all okay but the front was so out that you couldn't even insert a 0.05 feeler gauge. I adjusted the valves to the right settings and checked several times that they were correct before...
  5. XR
    I have recently purchased a XR250 project - Frame number HMME03-5700255 & Engine number ME08E-2314517 I'm trying to identify the year and model ? The cylinder head is off with a bent exhaust valve, and damaged guide. What might have caused this to happen :eek:
  6. Africa Twin
    Split the cases on 97 XRV750 but now during assembly the rear cylinder cam shaft sprocket timing marks slightly off...could it be off one tooth on lower sprocket, any suggestions? As you can see in attached photo the left side horizontal mark is about a half or quarter tooth below the right...
  7. For Sale / Wanted
    Hi all. Looking for front master cylinder for my 2002 xrv750. Part No. 45510-mv1-305. Can any one help ? Thankyou.
  8. Transalp
    Thought I'd post this up, to see if anyone has had a similar issue. A few weeks ago, my 1994 TA suddenly stopped firing on one cylinder. It had been running spot on when I put it away in the garage. Came to start it and it would only run on the front cylinder. I checked the CDi, and sure enough...
  9. XL
    I know it's a long shot but do you think this would work on an XL185? Piston 65.5mm Rings 250cc Big Bore Cylinder Kit for Honda ATC 200 XL200 223CM3 | eBay
  10. Africa Twin
    I have a crf 250 r front end complete wheel too i do need a caliper and m/cylinder but i am toying with the idea of an upgrade .I will wait until i have at least ridden my AT (which i have yet to do )but if any one has actual experience in this conversion i would be interested in hearing how it...
  11. Bikes For Sale / Wanted
    £3850 A 1975 Honda CB500 Four K1 UK model in good condition 25500 miles, UK registered from new not an import. The CB500/4 is VMCC eligible and qualifies for classic insurance and free tax, current MOT expires June 2018. The previous owner had the bike from...
  12. Dominator / FMX
    Does anyone know the size of hose used on the front and rear brake reservoirs. I need to replace hose that's between reservoir and master cylinder. (front and rear brakes). Would measure it, but want to get some ordered asap. Bike is an RD08
  13. Africa Twin
    I'm about to tighten the nuts holding the exhaust down pipe to the cylinder head on my 2002 RD07A. My Haynes manual tells me that the torque setting should be 27nm (or 20 lbft), which strikes me as a bit high considering that I've just done the same job on my CB1300 and the torque setting there...
  14. Bikes For Sale / Wanted
    SOLD Honda 1989 NTV600 Revere Vtwin shaft drive VMCC eligible £350 SOLD Soldvia Gumtree to a local Mileage 75000 bike stored since 2011 requires a new battery. Bike will start from jump leads and runs well engine and transmission good, alternator charges all electrics work. Brakes refreshed...
  15. For Sale / Wanted
    I have collected these over a number of years but need space in my shed they are in 4 plastic boxes. There may be more in boxes so just ask. I will list and if you need more info or an offer price send me a pm all parts in good order....Anything in red is sold. would take a price for the lot...
  16. For Sale / Wanted
    I'm looking for a decent condition front master cylinder from either an NX650 Dominator (1998 - 1996) or a Transalp 600 (94-96). Or possibly an XL125 Varadero (03-04). It's actually to fit to a Moto Guzzi V50, and I need an 11mm bore...... Any offers?
  17. XR
    Hi all, First of all, before you bite my head off, I am a total novice when it comes to engines and have only learnt a little through online research. I live in Hanoi and bought a used 2006 XR 400 (supermoto Japanese import). 10,000km on the clock. This is my first (big) bike and although there...
  18. Africa Twin
    Hi all, I posted here about 1 week ago about my 3 year old dead battery that caused one of my CDIs to stop working. Since then I have got a new battery (12v 14A gel battery) For a few days I had no issues, but the last 2 days driving my cdi has been acting up. This is what happens...
  19. Transalp
    Anyone want a 1997 Transalp? Need to pick up in Fife, Scotland. Good 10 months MOT. New tyres Brand new Hagon rear shock (100 miles) and all new linkage bearings on swingarm etc, and Powder coated swingarm, all sorted. New front forks and steering head bearings *Fuel* exhaust, all stainless...
  20. Chatter
    I know some of you are thinking it but far too polite to say it...:D:D:D My son called me today with some bad news about the carb he was going to ultrasound clean so I headed over to his work place and took my cylinder head with me to see if he could clean it before I strip it down to see whats...
Top