I'm looking to get some stiffer springs for a project bike (with unknown forks) and it could get expensive if I end up buying lots of different springs & rates new. It's been a little while since I had a Honda Transalp but think they might be suitable, so anyone got any old Transalp fork...
I was wondering if someone could measure the internal diameter of the tail pipe exit on the dominator exhaust for me please?
I got my domi scrambler running at the weekend but it's ear bleed loud so I want to design a baffle to go in the cans I'm running. From reading other posts...
trying to remove the headstock bearing outer race on my 2010 700 from the headstock but the inner diameter of the outer race is bigger than the shoulder it sits on :(
no edge at all to get to to knock them out.
Any tips or tricks ?
Just picked up a FMX 650 that’s had a replacement engine.
It came with the old engine that’s got a shagged piston but apart from that it’s in good shape.
I’m looking to buy a new piston and rebuild the old engine.
My question is can I use the same diameter 100mm piston from the XR650L...
Ever since Ive had the Transalp the seat seems to have been sitting a little high. Ive checked underneath a couple of times and everything seemed normal. Anyway today I had a closer inspection and noticed this pin seemingly not doing anything behind the bolt that holds down the fuel tank. It...
Does anyone know what size bolts are used, to attach handlebar mounts to the triple clamps.
Im looking to buy new mounts, I measured the length of bolt but didnt check bolt diameter, and looking on net, some use M12 bolts but some use M10
(or) I wish I hadn't bothered but it had to be done lol
My original standard silencer has some small holes in it so I decided to remove it and patch it up.
It was a heck of a job trying to get it loose from the downpipe but it finally came away or so I thought.
It had only taken the collector...
I bought a Dominator a few months ago because I want to improve my mechanical skills and a Domi should be simple and cheap.
So far so good.
The bike is in pieces right now - all according to plan.
The collar in the swingarm is in bad shape and I don't want to re-use it.
It has a lot...
Anyone know the INTERNAL diameter of an RD07A front fork?
There are quite a few fork valves on evil bay for other bikes for around £60 which might fit the AT but I need to know this measurement
Thanks for any help
Sent from my GT-I9505 using Tapatalk
I have a question would a Transalp XL 650 V 2000-2002 front wheel fit my Rd07 AT ? It looks the same IE twin disc and same diameter etc but I am not sure :(
Mine needs to be replaced as the valve came out of rim with the corrosion !! I found the Transalp wheel on Ebay and its close...
I am currently renovating my XRV 650 and I need new piston rings for it. Unfortunately I am having a very tough time finding a new set of these. The pistons are an oversize allready (I was told it was a 0.5 piston I measured the diameter, and it was 78.5 mm if this information has any...
Hello folks, me again :blob7::compress:
Does anybody maybe know the correct dimensions of the Dommie piston rings in STD setup?
(Inner diameter outer diameter and thickness of all three rings)
Its been a while since I dissassembled my clutch, and now I'm not 100% sure how to put it back together.
Number 7 on this, is a V-shaped ring. But I can't see which direction is has to be pointed.
in this scetch, should the SMALLER diameter of the ring be pointing towards the left of...
I have some troubles with my fuel lines on my RD04.
Wich INNER diameter should I use?
it seems the tank outpunt diameter is not the same as the input/output for the fuel pump and the inlet for the carburetor.
what diameter of tube should I use. I had never problems fitting those, but with...
I am with my front fork in pieces and as i have not one but 2 XR forks , i am thinking what would be the pros and cons. Both are 43mm in diameter.
The XR are cartridge forks, the front will be raised as the tubes are longer. The air buble bigger and in theory the whole dampening will be...
Hi all im in desperate need o a kick start idler gear xr250 believed to be 1986 ive bought 2 ebay purchaces and both are wrong so what i need is the idler gear with 24 teeth 6 holes in the gear 67mm in diameter and a 20mm diameter hole in the middle Please can someone point me in the right...
Both my taps on the Xrv don't shut off !
So rather than buy expensive replacements or repair kits I thought about getting and fitting in some other in line shut off taps.
Firstly what diameter are the fuel pipes from the petcocks and does anyone have any other ideas or thoughts ...