Honda XRV Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 40 Results
  1. Dominator / FMX
    Hello All, Please could somone measure the diameter of the FMX forks, the part that goes through the yokes, if possible I would also like to know the distance between the fork legs? Many thanks Jim
  2. Dominator / FMX
    I’m pretty sure all the above use the same basic frame, so the dimensions i’m after should be the same. Could someone with a Swing-Arm from one of these measure the front pivot width. That would be the outer width, i.e. the width required in the frame and also the inside width, i.e. the width...
  3. Africa Twin
    It's been a little while since I had the rear wheel of my RD03 off, and now I want to order some combined tyre levers and axle wrenches. Can anyone here tell me the dimensions I need? I seem to recall that it is 17mm and 24mm? I am currently in Scotland, and my bike is back home in Norway...
  4. Transalp
    Does anyone know the dimensions or numbers of front and rear bearings and seals ? I want to put some in my spares box before a trip and can normally source them through work :) List from lings site to help future readers front 6203 6303 30x56x7.5 seal 28x42x8 seal rear 6303 6304 6203...
  5. Dominator / FMX
    Does anyone have a Dominator frame and/or swing-arm handy that they could measure for me? I need to know the width across the front of the S/A i.e. along the pivot (or the width inside the frame where the S/A fits).I also would like to know the S/A length, i.e. from pivot to wheel axle (middle...
  6. Transalp
    Hi, I need a new o-ring for my fuel petcock. Rather than order an original honda part which will take a couple days to me (and possibly bug the honda place where I just picked up what I actually needed via another order), I was just going to source a generic o-ring for this tomorrow, then I can...
  7. Dominator / FMX
    Hello folks, me again :blob7::compress: Does anybody maybe know the correct dimensions of the Dommie piston rings in STD setup? (Inner diameter outer diameter and thickness of all three rings) Thanks! :thumbup::thumbup:
  8. Member Classifieds
    SOLD Kappa Givi Topbox Givi Monokey mounting plate £35 SOLD A Kappa Givi type topbox and mounting plate to suit. I think the box is about 45 litres the dimensions are Width 52 cm, Length 42 cm, Height 29 cm The box locking plate has been reinforced-see picture and there are some scuff marks...
  9. Transalp
    Got the kit to make one but can't find dimensions. Someone must have farkled one together before now. I did find a thread by a guy who'd knocked up a removable one that looked nice but he didn't share the design and it was a while ago.
  10. Dominator / FMX
    My engine mounts looked a bit corroded asked here for replacements and looked on e bay but none about so i'm going to have to knock some up myself I took them off today to measure and discovered just how bad they are As they seem to be a little bit rare at the moment i thought i'd put the...
  11. Transalp
    The nipple ends of these blighters often snap off. There might be a source of replacement spigot / nipple mouldings ... missus. Anyone able to supply similarly precise dimensions of a detached 'Long One' (Steady now, Alias) ? Thank You !
  12. Member Classifieds
    For sale is my Touratech branded Kahedo tank bag, it has a shaped semi rigid base to fit curved top tanks, a large A4 map pocket which is velcro'd do detachable, extendable by a couple of inches, has a couple of pockets & side bungees etc. It IS NOT magnetic, I've successfully attached it to the...
  13. XR
    Hi, Does anyone know where to source a 11.5kg/mm rear spring for a XR600RF (RG/RH the same) spring dimensions are 240mm x OD 82mm x ID 56mm In fact if anyone can recommend anything in the way of any upgrade tips or parts suppliers even second hand bits for the 600RF rear shocker it would be...
  14. Africa Twin
    Hi! I am considering replacing the cushion arm bearings, but I won't have time to order original parts (and the local Honda shop hasn't called me back after I requested a quote for the parts last week). I called up a local bearing shop to see if they stocked them, but they had a hard time...
  15. Transalp
    Hi Folks, does anyone know the dimensions of the centre stand main bolt, length and diameter. I've purchased one (ebay) which hasn't got it with it. Any help appreciated. Thanks.
  16. XR
    Hi, can anyone give me the the dimensions for a rear disc brake swingarm for xr250/400...i am looking for the distance from pivot to axle and the width of the swingarm at the pivot where it fits into frame as i am looking to convert my xl500s to rear disc. cheers
  17. Africa Twin
    Ordered a new stator from electrex world. The bike is a v plate 99 model RD07a they supplied a G07 stator, when I questioned them about it because it is 18mm & mine is nearly 28mm they said no it's defiantly right. Phoned again and was told the G08 is 28mm but is from an earlier model! Looking...
  18. Africa Twin
    Hi guys, I want to build by myself a central stand for my AT RD07A but I need a technical document of the central stand, sketch with dimensions. Could any of you help me with this? Thanks a lot, Bogdan.
  19. Africa Twin
    Does anyone know or have access to their carbs to give me dimensions (single and both connected)? I am in a process of building ultrasonic bath for cleaning them and would like to finish it and test before removing carbs from my bike. I found stainless steel dish 153x137x200mm (LxWxH) and I...
1-20 of 40 Results
Top