Has anybody got a heat shield for AT RD 07, the lower one that fits between the down pipes and the tail pipe, mines a bit battered and not happy with it, paint finish not an issue but must be quite straight and undamaged.
Hi All. Long time no post. I do hope you're all well.
My rear shock is getting a bit long in the tooth and I want to start looking to replace it. My bike is 100% road going these days so I would not be against a road set up rear shock, so does anyone know what fits? I know there are lots of...
Sorry! I have asked this before. I try to erase this post :-)
Since the RD04 handlebarswitces is impossible to get from new, I wonder if the RD07 switches fits on the RD04.
Anyone have tried this?
So, I've made the wp48 conversion with the single 320mm disc brake, the brembo calipers and the excel rim. The whole front end from a 450 sxf ktm. Now I've got a problem that I didn´t think of: I've got an analog odomoter and a digital pick up (magnetic) wheel and spindle. There's no space...
Does anyone have a Dominator frame and/or swing-arm handy that they could measure for me? I need to know the width across the front of the S/A i.e. along the pivot (or the width inside the frame where the S/A fits).I also would like to know the S/A length, i.e. from pivot to wheel axle (middle...
Hi i tried this today, Im not sure if it works on the road but it sits almost the same as my AT did. I fitted the swingarm from my 2000 AT onto my XL600v frame, The AT shock was too long but i tried the shock from a 650 TA and it slid straight in. It does look slightly lower than a pic of an AT...
Wondering if somebody could advise me please?
I need to replace the front Honda badge on the headlamp cowl after a respray. It fits above the headlamp.
Please can somebody tell me if the correct (factory) specification for this colour should match the Honda letters on the side...
I bought a new (to me) topbox and it came with a standard monolock plate. Apparently there is a specific plate for the Transalp 650 called E217, it also fits the Varadero. Is this correct? Did both bike use the same rack? Anyway, this specific plate is the one I already have but with some metal...
I'm struggling to find an Air Filter for a FTR250 Honda.
If anyone knows if an air filter from another Honda model fits please let me know.
Please note that it is for a FTR250 and NOT the similar looking FTR223.
Ever since Ive had the Transalp the seat seems to have been sitting a little high. Ive checked underneath a couple of times and everything seemed normal. Anyway today I had a closer inspection and noticed this pin seemingly not doing anything behind the bolt that holds down the fuel tank. It...
I was wanting to fit the Acerbis 23lt fuel tank to my RD08 but am advised it only fits the RD02.
Does anyone know whether it can fit with a little bodgery before I lash and just try it?
There will be the mounting of the tank itself and then the front fairing fit.
Any assist greatly...
Does anyone have an XR250s metal tank for sale (around 1996)? its an MD30 and has the single bolt at the back of the tank to fix and two grooves on the inside of the tank that slide onto rubbers attached on the frame. Part number 17520KCZ000ZA
If not - is there any other tank that fits -...
I have a rim from Hornet that fits Varadero as "plug & play", with matching brake disc 5 mm thick, I put original 150 mm rear wheel back on my bike so this is now surplus to requirements.
Also set of Metzeler Karoo 3 tyres with around 650 miles on them, for adventerous Vara riders.
Does any one have one of these for an RDO4 please ? the one i fitted for an RD07 is causing me a few problems.
it fits on the bottom of the rear shock
Also im after one of those stickers below for the front or know where i can get one please.