Honda XRV Forum banner

flatside

  1. Keihin Flatside.

    Dominator / FMX
    What do you think? Sorry about the picture quality. It has a metal gauze fitted to prevent small children and little old ladies getting sucked in. :D:D:D
  2. Kiehin Flatside problem

    Dominator / FMX
    My needle jet arrived from the US of A today so I stripped the carb down and cleaned it. I installed the neeedle and jets but there is a problem. The slide will not close all the way down and I have had it apart but cant seem to suss out whats up. If you look at the following youtube video and...
  3. Carb tuning

    Chatter
    I am about to try and tune my flatside carb when I get my bike started :D:D:D I used one of these on an old Z650 I had alongside a balancer guage I have. Do you reckon this will work on my Keihin FCR flatside that I want on my Dommie. I know these days we have gone digital with Co2 but I love...
  4. Its alive

    Dominator / FMX
    I got my Honda coil today and when I fitted it I got a spark. I just need my new needle from my mate in America then I can dial the flatside in and start this bike up. Just in case you forgot what it looks like :D:D:D Three years and alot of dole money in the making.:clown::clown::clown: I...
  5. Velocity stack

    Dominator / FMX
    Does anyone know where I can get hold of an aluminium velocity stack/ bellmouth with an inside diameter of 55mm or 2 1/4 inch for you old school chaps. Its for sucking small children and little old ladies into my Keihin FCR-MX flatside carb. I can only find them in the states and the price...
  6. Keihin Flatside modification.

    Dominator / FMX
    Has anyone fitted a flatside carb to their dommie? I have sorted out a RD08 inlet manifold and have the jets and needle required on order from a guy in Holland as they dont seem to be available in the uk and he has to order the needle from the Japan which will be another two weeks. I just...
  7. RD08 Carb inlet rubber

    Dominator / FMX
    My RD08 carb inlet rubber arrived today from Germany , it was only £20 but it was a 34bhp restricted one. A couple of hours with a rasp , file and fine sand paper and a lot of black dust it looks like I got a few more bhp out of the thing. All i need now are the jets and needle for my...
  8. Keihin Flatside.

    Dominator / FMX
    I am looking for an inlet manifold rubber for the Keihin flatside I bought for christmas. I have been looking for a GB500 one but they are as rare as a honest politician. The FX650 seems to be pointing to one side and the research I have done says that the carb should be on a five degree upward...
  9. Scouse B, Stard

    Dominator / FMX
    Just a few bits n bobs and its done. Two years of my time and the Danish tax payers money and were almost ready to fire it up. Just needs a new coil (I hope) a new chainguard and then once I have got it running I have a 41 mm flatside to go on it once I figure out the set up for it...
  10. Electrical problem continued

    Dominator / FMX
    I fitted a new ignition switch and another starter button and I still cant get the bike to start. I still only have power to the lights and horn. I have just ordered a flatside carb cos I thought I would get it going , I am seriously thinking of putting the bike into storage until junior...
  11. New Seat.

    Chatter
    I finally ordered the seat for my dommie project. The bike is at the electricians place awaiting completion and should be ready within the next week or so.:thumbup: I have ordered the top left hand seat and I have chosen chestnut as the colour:D:D:D This bike is going to be the dogs wotsits...
  12. Wanted/needed spanner monkey (xr650r) in or near exeter

    XR
    Hi, as I mentioned in another thread, I have bought my second XR650R. It is not standard. It has a full FMF exhaust, Mikuni 40mm flatside pumper carb, stage 1 hot cam and a modified air box. It starts and runs fine for (what seems like) as many miles as I want as long as I don't come down to...
  13. Flat tracker mod.

    Dominator / FMX
    I have been offered a flatside carb for my flat tracker project thats been on hold for a few months and was wondering if any of you guys have done this modification. The part number is 16100-MEB-671 . Is it worth getting to fit on my dommie?:thumbup:
Top