holes

Started to change the output shaft on my 700 XL. All the bolts holding the chrome heat shields and the painted heat shields were sized in so that took me around 4 hours to do, I’m a slow worker, drill out re-tap the holes and order new bolts. The rest went as I expected it to no real drama...

Im Looking for tank badges/logo for my CG125 tank. The spacing between screw mounting holes is 60mm, but all the badges i can find on fleabay are 67mm spacing between holes. Anyone bought any of these in the past for their CG125 tank with 60mm hole spacing?

Im Looking for tank badges/logo for my CG125 tank. The spacing between screw mounting holes is 60mm, but all the badges i can find on fleabay are 67mm spacing between holes. Anyone bought any of these in the past for their CG125 tank with 60mm hole spacing?

Anybody have a rear rim (with or without hub) that's 17 inches? I think all the XL versions should be 36 holes. Need to re-lace a wheel, let me know if anyone has one they can part with.

The rear shock on my RD04 is really harsh at holes and bumps, and it goes thru the whole bike. Its feels like the compression damping is too hard. I have tried to adjust it, but I can’t feel any difference. I have 30 mm free sag, and 70 mm rider sag, so the spring should be ok. (from the...

Help needed please guys. Decided to try and get my AT running over the festive period. Not a hope. I'd forgotten to drain the fuel when i put it away a couple of years ago. I know, it's a crime to put it away for so long, but i did. Well, it would not start, so i stripped and cleaned the carbs...

anyone here want this? before i bin it.... there's no holes in it

My AT's on it's third headlight fairing (or 'nose cowling' as the parts book calls it). The first two developed bad cracks around the holes into which the side fairing panels connect. I've kept the old fairings with an eye to trying to repair them and have now, after many years, got a plastic...

I have finally received my new starbars ready for fitting at the weekend. Question I have is this....the original bars have holes for the instruments, do I drill new ones or remove the bits that slot into the holes on the instruments? cheers in advance

I am using this site to try and order some bolts that I require to put the original backend on the bike https://www.fowlersparts.co.uk/parts/5157420/xrv750v-1997-e/seat-2 question I have is this, to order the bolts for the carrier(I have the collars) it shows bolt number 27 for the middle...

I bought a new (to me) topbox and it came with a standard monolock plate. Apparently there is a specific plate for the Transalp 650 called E217, it also fits the Varadero. Is this correct? Did both bike use the same rack? Anyway, this specific plate is the one I already have but with some metal...

So my Transalp Gaiters have more holes than swis cheese and look unsightly. So a few questions 1. Can I just remove them and not replace? Alternatives available? 2. How hard is it to remove the forks and put them back properly? 3. How hard is it to align them once back in? do they just 'fall...

You know that moment when you poke something with a screwdriver and immediately wish you hadn’t... I found a bit of flaky paint around where the seat and silencer bolt to the subframe, off side. One poke with a screwdriver later, I had a hole. After a friend attacked the affected area with a...

AKRONT WHEEL: (very good condition, Fresh Truing done) - AKRONT 18'' 3.0, 32 holes rear Heavy Duty Rim: USED (good condition, signs of ware, no rust) with Heavy duty spokes (v. good condition) - Originat AT Hub: USED (v. good condition, signs of ware) - 5XJerk Damper (almost new) - Original AT...

Hi I have a XRV RD04 1991. Reading all service manuals and visiting all websites in the world, don't clarify which needle jet holder goes where. One have 6 holes - one have 10 holes. My logic tells me, that the one with 10 holes is in carburettor 1, since its jetted a little larger than...

One only. Guy asked me to make one & sold his bike in between! 200 x 100 overall with long edges folded back 22.5 degrees. Mounting holes are clearance for M6. Made from Stainless Steel with brushed polish finish. Stand off bushed will be needed but suggest using oversize nut or similar. Thanks...

(or) I wish I hadn't bothered but it had to be done lol My original standard silencer has some small holes in it so I decided to remove it and patch it up. It was a heck of a job trying to get it loose from the downpipe but it finally came away or so I thought. It had only taken the collector...

Hi all, Hope everyone is well, I'm looking to get a spare set of rims for my RD03 so I could have a set with 80/20 tires and a set of full knobbly tires on. Could anyone help decode the stamping on the rim: "J 21x1.85 3 88 DOT" So the 21x1.85 is easy enough, what does the J and 3 88 DOT...

Good day all.. I come to you in need of advice/assistance if I may? I own a Honda Transalp XL650V (2007) and my exhaust silencer has sprung several holes. I've been looking for a Genuine replacement but haven't had any joy as yet. Can anyone recommend a good replacement or know of genuine one...

Good day fellas. Since I'm rebuilding the bike into a 22nd century machine I figured it might be worth it to adjust the rear accordingly too. Does anyone know if the XL650V rear led light could fit on the XL600V? There are heaps of 650 assemblies available on eBay: Complete Rear LED Tail Tidy...