Honda XRV Forum banner

Discussions Showcase Albums Media Media Comments Tags

1-20 of 30 Results
  1. Africa Twin
    Hello there! I was rebuilding my carbs while looking at the Honda fiches, and saw that a gasket on my carb is positioned differently. On the fiches, the order is: 28-1-15, so the metal collar (15) sits on the carb, the gasket (1) sits on the metal collar, and the plastic plate (28) sits on the...
  2. Dominator / FMX
    Evening all sorry to bring up this issue again but had my speedo checked today 1999 Dommie and the splines on the blue cog in the housing driven off the front wheel is knackered does anyone know where I can get this single piece as opposed to having to buy the whole kit thank you. Jason
  3. Dominator / FMX
    I just performed an oil change on the FX650 Drained out of the frame, crank case and filter housing. I put exactly 2.15L of oil in (10 minute interval inbetween) Bolted everything back up and checked the oil level, it is almost the entire length of the dipstick I'm aware the oil check ritual...
  4. Africa Twin
    Is the original rear shock ,silencer and throttle housing off a RD04 the same as the RD07
  5. Varadero
    Had one on order for 9 months! It's the early round type, the later ones won't fit into the back of the lamp housing. Getting desperate now!:lol:
  6. Africa Twin
    Has anyone ever tried to fit a digital speedo with a magnetic pickup inside the stock speedo housing? This could be a solution for keeping a stock look, but not dealing with that nylon gear packing up all the time. Also, it would allow for easily switching between MPH and KPH. Talk me out...
  7. Transalp
    Hi all, Ive now taken the grips off the Alp but I cant seem to find any grips to fit. For some odd reason most grips seems to be 120-125mm long, whereas I have about 95mm throttle side and 90mm clutch side. Did the 600 Alp come with shorter grips? :confused: I could move the various 'bits' like...
  8. Off Topic Lounge
    Found this inside my petrol tank. Its a magnet inside a plastic housing. Some sort of debris catcher? Anyone seen one before? Or maybe one of those "petrol energizer" gadgets. Might just put it back. It hasn't caused any problems in the 5 years I've had the bike. Sorry about the trebled...
  9. Africa Twin
    Hi, I need to source the rubber link section that goes between the Air Filter housing under the seat, and the other Airbox thingy that sits on top of the carbs - mine has split! Any idea where to source one? Am i best going to my local stealer, as searches on a well known auction site appear...
  10. Dominator / FMX
    Hello people, I'm in desperate need of a 1988 rd02 front caliper There is a bike being broken on the bay but seller slow to reply What if any other options do I have ? Any other callipers fit ? any one on here know of any I have new pads piston bleed nipple and seals just the housing I need Any...
  11. Africa Twin
    Number 2 on picture Does the swingarm need to come off first or is there an easier way?
  12. Africa Twin
    Hi Folks, I'm in the process of replacing the speedo plastic gear thingy and have hit a bit of a problem. The old isn't in too bad a condition and slides in and out of the housing no problem but the new one slides in so far (I've given it a good greasing) then feels slightly stiff. I'm...
  13. XR
    Heat from the exhaust gases is frying the rear indicator housing and vibration from the exhaust destroys the bulb! Is there an off the shelf bracket that will move the right indicator below the line of the exhaust and into fresh air? Or is there an angled extension/deflector tube to fit the...
  14. Dominator / FMX
    Hi iam new to this forum just bought an slr 650 and in the middle of an engine swap , can anyone tell me any differences between the slr engine and a vigor one ? the vigor one has a housing on the left side off the engine with hose take offs and was wondering what its for .. cheers
  15. Africa Twin
    Just wondering if anyone knows where I can run a vacuum line to operate a scottoiler on an RD07. Can't see any vacuum hoses off the carbs but there may be a plug on the carb housing that I could connect a nipple and line to the unit?
  16. Africa Twin
    Hello; Whilst the shock is off for a service and respringing session, I took off the linkage. The bearings seem OK but I'd like to give them a through clean. The old grease has gone a bit congealed and some roll less freely than the others. Is it possible to pop the rollers out without removing...
  17. For Sale / Wanted
    I was wondering if anybody has a rubber fuel pump housing for XRV 650. Thanks in advance.:thumbup:
  18. Varadero
    Well iv been rebuilding my Varadero 2000 model Need a little help... I have no idea what connects here and where the corresponding pipe goes This is a picture of the thermostat housing on the bike, with the mystery tube connection Can someone have a look at there's and let me know what...
  19. Africa Twin
    I need a new fuel tap for my RD07 as a leak has developed from the tap housing. I haven't managed to find a standard replacement and I was wondering if anyone on here knows where I can get one? Has anyone used a fuel tap from another type of bike? Or does anyone know of other bike models that...
  20. Suzuki
    Hello, I'm new to the forum - I've been pointed here by a fine member of BCF as I may be able to get some info. Changing my oil/filter yesterday I found a crack in the 'filter housing' (not sure of the proper name!), along with two other tiny ones. I'm told this is not uncommon and should be...
1-20 of 30 Results