In the box of parts that came with the '89 NX650 that I just bought, I found the metal plate/sticker that shows the VIN, tire pressure info, model year, etc. Where does this thing belong on the bike? I want to glue it back on, but I can't find it on parts diagrams.
Being a vertically challenged 5’7 90kg with 30” inside leg I might need to lower my (new to me)Xr400r a tad!
ive bought a second hand seat and will be sending it off to get the foam shaved down a bit and a new seat cover but think it might not be enough!
Was considering a lowering link but it...
I have been lucky enough to be the new owner of an 96 XRV750. As we all know there are not many here in the US and I'm excited to get her on the road. I'm working on rebuilding the motor and I can not find info on what grit of hone to use to re-ring. I have factory rings and the bores...
Greetings, I'm hoping someone can shed some light on a little bump in the road I've come across in my build. As the title states I've thrown a NT650 / Bros 650 / Hawk 650 motor in a Transalp frame and my issue is the front cylinder's exhaust port isn't allowing me to get the Hawk's front header...
I am looking for a pair of pistons ( 0.25) for my RD03. ( 13102-MN8-305 )
So far, all websites with OEM parts doesn't have it anymore.
Maybe somebody can help me with some info.
I already bought the 0.25 rings, and prepared the cylinders, all I need is the pistons.
Been a while since i last posted.. moved house, got a car, started a family etc, so the rebuild of the RD07A was put on hold... until now :)
I am in need of either... some new (second hand) brake calipers (front and back) or info on where i can send my ones for a full refurb etc...
i have just purchased a transalp 650 from a friend who had it stored in his garage for the last 6 years
its only done 6,800 miles from new on a 2002 model
the battery was completely flat and being from someone i know i purchased it
upon getting it delivered the next day i replaced...
Greetings from Denmark..
I havnt been on here for a while because I have been busy building other bikes...
I want to build a cafe racer from a Dommie with a single sided swing arm and usd forks like this one I found on the net.
I have bought a single sided swing arm from a VFR 750 F with a pair...
I've just won this ebay auction for a CT90 needing a bit of work. I'm after peoples thoughts on if they think it's a good deal, and anything I should check when I go to collect? It was a bit of a last minute impulse buy.
Thanks in advance,
I decided to change my coolant recently and found that when i replaced the drain bolt with a new washer it wouldn't tighten properly. I removed the bolt and found that what appeared to be the thread from inside the drain bolt hole had come away and onto the bolt. I decided to buy a new bolt to...
I have a collection of spares for both XL 125 and 185S models from around 1982 accumulated by may Father over the last 10 years that I feel deserve a better home than the corner of the garage
185 Drum Forks
125 Disc Forks
Front and rear wheels with Drum Brake
Front Wheel with...
I am about to receive my first XL, in fact my first Honda and I am very much looking forward to it.
It’s a 1982 XL250SA and it is bought unseen by me so I am taking a big gamble but the bike is 200 miles away so a specialist courier is collecting it.
I would like to know more...
I’ve just picked up a 1979 Xr250 which had been left outside without a spark plug for probably several years. The top end is very rusty, there’s a hole in base of barrel (outside into cam chain chamber) and also quite a bit of play in con rod.
These xr’s are not very common over here in...
Anyone got any info or advice on the acceptable or expected oil pump drive chain slack when installed (or length between links if removed) for a 1994 XL600V?
Engine casing off as we speak and im mid clutch replacement but when I look at the oil pump chain ,it just looks to me to be very loose...
Just a heads up folks on this new gadget ive got to play with ... its a real time tracker £35 of fleabay .... ive got it for my van but can use it on bikes cars ect ect ... i did a bit of reading before i got it and there was mixed reports but for the money i took a punt...