Honda XRV Forum banner

inlet

  1. Yamaha MG1-T Trailmastera predicestor of XT1200Z Super Tenere

    Yamaha
    saw this on display at Spa Motorcycles , Cheltenham A 1962? MG1-T Yamaha's competitor against the Honda CT200 & CT90. Very rare in UK, only one?, I had never heard of them before today. 80cc rotary inlet valve 2-stroke engine 4 BHP
  2. RD04 1990 : where does this screw go??

    Africa Twin
    Hi guys I'm Marco from Belgium. I have an RD04 from 1990. It's a great bike, but has had some bad owners that didn't maintain it. :( I have replaced the rubber inlet seals, valve cover seals, fuel hoses, blablabla... =) Now i am left with one part: a screw, a tiny washer and something on...
  3. NX650 Service manual newer than 88-89?

    Dominator / FMX
    Just wondered if anyone ever found or has a service manual for the NX650 Dominator for models newer than 88-89? The 88/89 is the only one I can find so far, and it's missing a few things for newer models such as my '95, for example the rear disk brake, the shorter inlet manifold, the different...
  4. XL500s-Z crank case breather

    XL Technical Specs
    Hi all - I have a US spec '79 XL500s-Z and I want to eliminate the US crankcase breather/collector, does the UK version have a plain pipe from crank case to air inlet rubber? Has anybody any other solution? thanks!!
  5. Keihin Flatside modification.

    Dominator / FMX
    Has anyone fitted a flatside carb to their dommie? I have sorted out a RD08 inlet manifold and have the jets and needle required on order from a guy in Holland as they dont seem to be available in the uk and he has to order the needle from the Japan which will be another two weeks. I just...
  6. Keihin Flatside.

    Dominator / FMX
    I am looking for an inlet manifold rubber for the Keihin flatside I bought for christmas. I have been looking for a GB500 one but they are as rare as a honest politician. The FX650 seems to be pointing to one side and the research I have done says that the carb should be on a five degree upward...
  7. Wanted: MT250 Elinsore Parts required.

    For Sale / Wanted
    A few parts required to go on a '70's MT 250, I think may be 125 or 185 parts are the same? Rear Brake Plate Arm, Cable to suit, Carb' and inlet manifold and a n/s Side cover that goes over the oil tank. Might consider a donor bike if necessary. :rolleyes:
  8. Wanted: Used front RD03 brakeline

    For Sale / Wanted
    All I need from the brakeline is the top steel block. Could come from another bike if the upper block is the same. Would buy several if available. Also need ASAP the plastic inlet for the rear MC. Mine is broken at the neck. Part # 43503-MS8-006 and available on most Transalp...
  9. XL650 V6 Valve Covers

    Transalp
    The Haynes manual 3919 says that the inlet valves are covered by a cover and the exhaust valve is covered by a cap. My bike seems to have covers for both. Is that normal, maybe an evolution towards the 700? My bike is a 2007, so the last year of the 650.
  10. Carb inlet Rubbers

    Africa Twin
    Hi, Just got myself a RD04 which is restricted by the inlet rubbers. Is there an easy and hard way of replacing them ? Cheers Bob.
  11. Purpose of fitting 45127-KA3-831 on master cylinder

    Africa Twin
    The MC inlet isn't the usual European 10mmx1, but rather 10mmx1.25 I suspect My RD03 didn't come with the hydraulic fitting pictured below. What is its purpose? Could it be an adapter to a 10mmx1.0 thread? Part # is 45127-KA3-831 and found on many Hondas
  12. Wanted: wanted slr650vigor carb inlet

    For Sale / Wanted
    wanted slr650/vigor carb inlet rubber and associated pipeworkc
  13. Fuel Exhaust

    Transalp
    Just bought a Fuel Exhaust for my 650 Tranny and on their website it says this for sealing the exhaust connection: "You can use everyday bathroom and shower sealant as long as it is silicone based. Just use it sparingly around the inlet of the end can and also inside the pipe which mates up...
  14. Back firing through airbox

    Africa Twin
    Occasionally, and normally when blipping the throttle when not under load, either cornering or at lights etc - I get a back fire into the airbox. You feel a momentary loss of power and then its fine again. Anyone know where to look, is it an inlet valve or more likely a fueling issue?
  15. XR500 1983 Cam followers

    XR
    Hi everyone, been lurking around on here for a few months enjoying the chat but, what d'ya know, now I need some help, or information if anyone can help. I have a XR500 1983 I think, the engine type with "RFVC" cast on the rocker cover, anyway, the inlet valve cam followers are toast and need...
  16. How to open the air inlet at the airbox

    Africa Twin
    Hello guys I was wondering which is the right way of opening the air inlets on a 98 airbox if youy want a better breatheZ???I mean an AT box!!!!
Top