Honda XRV Forum banner

inside

  1. Lowering link for a 2002 Xr400r?

    XR
    Being a vertically challenged 5’7 90kg with 30” inside leg I might need to lower my (new to me)Xr400r a tad! ive bought a second hand seat and will be sending it off to get the foam shaved down a bit and a new seat cover but think it might not be enough! Was considering a lowering link but it...
  2. Fixed my neutral switch....

    Transalp
    I was told it was intermittent when I bought the bike, and had been checked out and nothing seen to be wrong. So, investigations were made, and I soon discovered it barely reached the contact point inside the gearbox. I’ll probably order a new one, maybe, and I didn’t want to leave the copper...
  3. SLR, FX, FMX Swing-Arm

    Dominator / FMX
    I’m pretty sure all the above use the same basic frame, so the dimensions i’m after should be the same. Could someone with a Swing-Arm from one of these measure the front pivot width. That would be the outer width, i.e. the width required in the frame and also the inside width, i.e. the width...
  4. Swap: Transalp 700 lowered saddle.

    For Sale / Wanted
    My transalp 700 standard Honda seat has been lowered,has a sticker inside stating so. I am 6.2" so prefer standard seat,if anyone needs a lowered one would swap. Cheers, Dave
  5. Rugged Roads XRV Indicators question

    Africa Twin
    Hi all, If anybody has bought the indicators from rugged roads could you please tell me what bulb it uses, If it has the foam seal inside like the oem does ? And is the lens the same as the oem? If you could upload a photo of the rugged roads lens & bulb it would be great :) Here is one...
  6. Left side Switchgear

    Dominator / FMX
    Anyone chopping up their bike and no longer need the left side switchgear? My indicator switch has just snapped inside and could do with a replacement. Thanks!
  7. Lost key

    Varadero
    hello, My friend and neighbor only had one key for his xl125v 2002 and has lost it,he has searched everywhere but no luck,he has a very active toddler who may have chucked it,anyway can anyone tell me where the key number is located on this model,would it be on the inside of the petrol cap?under...
  8. Swing-Arm dimensions

    Dominator / FMX
    Does anyone have a Dominator frame and/or swing-arm handy that they could measure for me? I need to know the width across the front of the S/A i.e. along the pivot (or the width inside the frame where the S/A fits).I also would like to know the S/A length, i.e. from pivot to wheel axle (middle...
  9. Dommie build - rear peg options

    Dominator / FMX
    Right, im looking for some ideas to mount rear pegs on my dommie project. Would prefer them to be removable, as they will only be fitted if i take my son for a ride. See photo below. The only idea i could think of, is two weld two nuts on the inside of the curved upright, so i could then bolt...
  10. For Sale: TCX infinity gortex boots size 45 uk 11/11.5

    For Sale / Wanted
    SOLD TCX infinity gortex boots size 45 uk 11/11.5 100% waterproof leather gortex boot in excellent condition and up to now best boots I have had. Easy to walk in and light. They work well in summer and winter neither to hot or to cold and since buying these have never had wet feet. I dont think...
  11. Bar ends and renthals

    Africa Twin
    My AT has a set of bars on that are too short for the handgrips(a cheap quick replacement by the previous owner). I have the originals but they are slightly bent, so rather than powder coating them, I was lookig at the Renthal Enduro high bars. Question is...will the original bar ends and...
  12. New Africa Twin build videos

    Africa Twin
    In a general search for motorcycle factory build videos found these for the CRF1000 AT, better than the Christmas edition of?? 2016 Honda Africa Twin CRF Production Line / Assembly Videos & Pictures - Go inside the Manufacturing Plant! | Honda-Pro Kevin
  13. Engine casing wear from crankshaft - trouble or not?

    Africa Twin
    Hi all, i am new to this site and need some of your collective wisdom. i am rebuilding my RD07A and have come across unusual wear on the inside of the crank cases that looks like the crank rubbing against them. I cannot find any thrust washers or any method of adjusting crank lateral movement. i...
  14. For Sale: RD07a Front and Rear rims fr sale

    For Sale / Wanted
    RD07a Front and Rear rims for sale. NOW SOLD NOW SOLD As title, I have a pair of rims from a 2001 RD07a. Anyone interested before I stick it on eBay? good condition, very small bit f corrosion on inside near valve hole but perfectly usable. Can send pictures if anyone interested.
  15. XR250S Metal Tank

    XR
    Hi, Does anyone have an XR250s metal tank for sale (around 1996)? its an MD30 and has the single bolt at the back of the tank to fix and two grooves on the inside of the tank that slide onto rubbers attached on the frame. Part number 17520KCZ000ZA If not - is there any other tank that fits -...
  16. 1995 600 size of collector outlet

    Transalp
    (or) I wish I hadn't bothered but it had to be done lol My original standard silencer has some small holes in it so I decided to remove it and patch it up. It was a heck of a job trying to get it loose from the downpipe but it finally came away or so I thought. It had only taken the collector...
  17. XL600v to XL650v

    Transalp
    Had to retire, for now, the 600. Got myself a very nice condition 650. Couple of issues i've seen so far : The facia on the clocks is very difficult to take off, I need to change the indicator relay for LED one, not easy to get it off. I've taken all the screws that I can see out, have even...
  18. Wanted: 96 XRV Rear Rim wanted.

    For Sale / Wanted
    Hi folks , so yes my rear rim has turned into the magical Japanese dust from the inside ! Has anyone got a suitable rear rim for sale for my P reg XRV :D
  19. Honda Xr250r 1993 crank case

    XR
    Removed my crank as it needs a new con rod , but the crankcase inside has a section that the crank sits in and there is a hole init , will this matter im sure its designed for some reason like to hold oil to lube the crank but with a hole this will reduce it ? . Does anyone have a set of cases...
  20. Moving coolant tank on RD07

    Africa Twin
    I am currently drafting auxiliary aluminum fuel tanks for my RD07. On the left side, the mosfet regulator can easily be moved inside the toolbox under the seat. What about the coolant reservoir? Has anyone found a different location? It can't be moved to where the RD03 coolant tank sits because...
Top