Anyone know the INTERNAL diameter of an RD07A front fork?
There are quite a few fork valves on evil bay for other bikes for around £60 which might fit the AT but I need to know this measurement
Thanks for any help
Sent from my GT-I9505 using Tapatalk
I have a spare engine for sale
It came with a job lot of parts, I only needed the other parts so this engine is redundant
It has apparently 30k on it, there is some wear on the output shaft, other then that it looks to be in decent condition
Obviously I haven't run it so can comment on its...
i'm having trouble splitting the bottom engine case on my 82 Xl500r,
i have to replace the kick start return spring, i have the engine upside down on the head & I've removed all the exterior screws, are there any internal screws i have to remove & what is the best way to separate them...
Hi guys, I'm rebuilding my starter motor as it went caput, stripped it all down put new brushes on and cleaned up the commutator and output shaft, and got all the bloody oil out of it.
The problem I'm having though is sourcing the internal bearing and oil seal that sits in the end of the...
Hi is the kick start on an xl 600 the same as on an early nx650 dominator, are
the internal fittings compatible with the dommie I have a spare xl600 crankcase cover I was wandering could it
be an easy fit?
I bought Barkbuster hand guards to fit to my RD07A. Of course it doesn't fit the standard handlebars with the internal handle bar weight in place. As I see it my options are:
1. Drill and tap the internal weight and fit the BB's to it.
2. Remove the internal weight and fit the BB's to...
Can anybody throw some light on this for me, as I've never had an AT with a Tripmaster before.
I turn the ignition on, the Tripmaster screen lights up OK, but there's nothing on the LCD panel.
I've pushed reset; I've held reset; but I get nothing.
I bought this Tripmaster but it hasn't been...
and seals for my brakes - spent today cleaning out the new ones - nice and sparkly (going matt black soon) and I need everything - pistons, seals, both internal and external. Looked at Wemoto and ebay, anywhere else?
Hi guys, in the **** a little. Stripping the clutch and i've found there is no thrust washer at the bottom of the basket, urgently require the thickness and outer dia of the washer if anyone knows?? Not to concerned with the internal dia as i'm thinking all it has to do is clear the shaft.
Can anyone point me in the right direction of the rotor puller for this bike. Got sold a puller to fit but its too big (its the two part one) 27mm 1.0 LH thread.
Done a bit more research and it appears the 22mm x 1.5mm RH thread (internal) should do it - but want to make sure this time...
When I bought my @ it had a noise coming from the inside of the clutch casing, it sounded to me as if something was catching / rubbing inside so I decided not to do many miles on it until I had had a chance to look inside. Well, I've drained the oil and had the casing off today and from...
Not the most reliable and impartial source I know, but still:
Has anyone heard about this - is this for real?
Isn't 'democracy' grand :rolleyes:
Looking on the bright side I suppose at least we'll all be...
Can anyone suggest some good internal bags for my Alpos 38 ltr and 41 ltr hard luggage? I don't want bags that fill the whole boxes but ones I can use to segment my kit. (e.g. books/maps, electricals, toiletries + medical, paperwork, camp-cooking kit, etc.) I'll probably keep clothes, tent...
Do frames rust on the inside? I saw a small hole at the front-left (near the down tubes) which gave me that sinking feeling as it looked like it had been made by a stone at first.
But on closer inspection it looks too square.
This is barmy surely, having a nice entrance for...
I noticed the other week a noise coming from within the engine on the XR.
It's only at a certain revs.
Of course its difficult to describe a noise, but I'd liken it to a noise that a metal exhaust guard would make if it was slightly loose. Very metallic. Fine when the bikes on tickover, but hit...