Search Results for ‘keihin’

Does anyone out there have any experience of fitting a Keihin FCR41 Flat Slide Carb to a Dominator? I was told by a carb specialist that this would be an improvement and a little more power. If so, how hard is it and what would I have to do .? Thanks in advance Ian Melrose

HONDA NX 650 DOMINATOR KEIHIN CRF 450 CARB | eBay Are you looking for a flatside carb for your dommie

I have just fitted my flatside carb to my Dommie and was wondering which of the two push/pull controls is the choke? I know one of them is the choke but what is the second one for and which is which? :thumbup:

What do you think? Sorry about the picture quality. It has a metal gauze fitted to prevent small children and little old ladies getting sucked in. :D:D:D

I am about to try and tune my flatside carb when I get my bike started :D:D:D I used one of these on an old Z650 I had alongside a balancer guage I have. Do you reckon this will work on my Keihin FCR flatside that I want on my Dommie. I know these days we have gone digital with Co2 but I love...

Does anyone know where I can get hold of an aluminium velocity stack/ bellmouth with an inside diameter of 55mm or 2 1/4 inch for you old school chaps. Its for sucking small children and little old ladies into my Keihin FCR-MX flatside carb. I can only find them in the states and the price...

I am looking for an inlet manifold rubber for the Keihin flatside I bought for christmas. I have been looking for a GB500 one but they are as rare as a honest politician. The FX650 seems to be pointing to one side and the research I have done says that the carb should be on a five degree upward...

I am in a bit of a better mood today because I just got my Keihin FCR 41mm carb off the courier. All I have to do now is suss out which boot fits and find the required jets and needle which will have to wait until January as I have blown my savings. :clown::clown::clown: I think I will wait...

I have been scouring the net to find a carb needle and jets to set up a Keihin FCR 41 carb I found on ebay. Allens dont have the needle and the only places I could find one is in the states which will take forever to get here. I found one in Holland but they want €40 for it. :mad::mad::mad: Any...

i am thinking while I have the carb off to try to fix my lack of tick over to try to find an extended mixture screw as the originals are such a pain,I can find plenty listed for keihin FCR carbs but none for CV carb. Does anyone know are they interchangable or have a source for one for CV carb

edited double post,cant seem to delete it

My first post - Hi from the heat & humidity of Darwin, Northern Territory Australia people. Has anyone tried installing aftermarket carbs to their AT, such as Keihin FCRs or the like? If so was it a success? Many Thanks Nick (wantok)

Hi would be interested to know if anyone's got a keihin fcr 41mm carb on there bike. And how much of difference it made to the bike.

Hi all, I spent an hour taking my carbs off, yet again, on my KLE500. All atempts to get the bike running properly have been in vain :confused: So this week I ordered a couple of carb kits off the internet. I was informed by another member of the forum (thanks Lee) that the float needles were...

Hi All, I am looking to see if I can source some carb main jets for my RD07A so I can try re-jetting to improve the fuelling after fitting a Leo Vince SBK titanium can and pipercross filter. I have 115 standard jets front and rear and am looking for some jets sized above and below this...

hi folks, just a quick one in the way of advise, has anyone ever fitted a "keihin fcr 40mm flat slide carburettor" on an xr 400, if so how did it improve the bike, and how did you install the throttle position sensor, if at all?