Honda XRV Forum banner

Discussions Showcase Albums Media Media Comments Tags

1-19 of 36 Results
  1. Africa Twin
    Looking to replace all the fuel lines on my RD03 as a couple more leaking a bit nowadays. Rugged roads has 4or5 sizes. What is most common I would need? I plan on buying some bulk lengths. They have 4.5, 5.5, 7.3 and 8mm ID. Mine are so old going to be hard to determine sizes. I know I have used...
  2. Transalp
    After taking my calliper apart to clean the pistons and bores and to replace the seals I made the error of not taking photos of where the two clips/shims go !! I've ordered a manual but until it comes can anybody help? It's a twin piston calliper off a '93 transalp and there are two stainless...
  3. Africa Twin
    Hi I have a XRV RD04 1991. Reading all service manuals and visiting all websites in the world, don't clarify which needle jet holder goes where. One have 6 holes - one have 10 holes. My logic tells me, that the one with 10 holes is in carburettor 1, since its jetted a little larger than...
  4. Africa Twin
    Hi guys, Its been a while since I dissassembled my clutch, and now I'm not 100% sure how to put it back together. Number 7 on this, is a V-shaped ring. But I can't see which direction is has to be pointed. in this scetch, should the SMALLER diameter of the ring be pointing towards the left of...
  5. Transalp
    Does anyone know what larger brake discs can be fitted to a TA600? I know you need the caliper adapter, but I am not sure what models of Honda have the bigger disc you can use. I know the Honda "hawk"/NTV 650 is ok, what about the Pan European? Or the Deauville?
  6. Transalp
    Hello, Does anyone know where one can find a larger fuel tank for the Transalp 700? K
  7. Helmets
    Yes I know about SR2 but looking at SR1 now =) Head size 61cm: According to Schuberth size chart: L = 58-59cm XL = 60-61cm Today I have: Shoei XR-1100 L = 59cm Fits good but can't be larger and Medium is to small. Uvex × 2 L = 59-60cm Feels quite large but also very light with soft...
  8. XR
    I am fitting the 280 kit on my 2004 xr250l I am running standard air box, snorkel removed, k&n filter. 250 r larger header pipes to FMF Q4 pipe Mikuni 88cv carb and 1000ft above sea level Any ideas on where to start on jetting the carb Thanks
  9. Africa Twin
    Hello! I have had some problems with popping on the overrun on my rd04-90. I was going to change the header gaskets but is confused about the sizing of the front gasket. On 91 up it is supposed to have the larger one in front. I have bought both to try and the larger one fits very nice in...
  10. Transalp
    Morning All, I have a memory problem, ( it happens at my age :rolleyes: ). I've installed new bearings on my front wheel but for the life of me cannot remember how the larger one fits regarding the speedo drive. Its seated flush at the moment but am I right in thinking it should go further in...
  11. Africa Twin
    I went to the NEC show today, and had a look at the design exercise that's been talked of as the new AT. I had to peer through the ersatz "mud", but I suspect Honda will need to do a lot of relocation of sensors, or provide a much larger "sumpguard" before the bike could be used off-road in...
  12. Transalp
    Am about to replace my 15 tooth gbox sprocket with a 16 tooth. The 16 is noticeably larger of course. I will be replacing the chain and rear sprocket (47 tooth). Any issues I need to be aware of? Will a regular replacement chain fit?
  13. XL
    Hi, can anyone tell me which is the Headlamp lighting coil ...... ... is it the small paper covered coil or the one that sits on top of it or the larger coil that sits opposite the other two coils. cheers
  14. XR
    good morning all, i have what i belive to be a 1982 xr250 in a box or box,s !!!, the rear spindle was missing so found one on ebay unfortunatly the spindel is to short for the swing arm and the diamiter of the spindel is also to small for the wheel barings could this be an earlyer model or a...
  15. Transalp
    Anyone who may have fitted a 16t sprocket to their 650 did you get any problem with the case saver. I have fitted a genuine RD03 sprocket and have given the case saver a bit of a grinding down to clear the larger cog but Ive gone as much as I want to and it still sounds pretty noisy. Wonder if I...
  16. Dominator / FMX
    Does anyone know if an early transalp fuel tank would fit onto an fx650 frame without too many mods. (I want it to remain possible to revert back if necessary.) Or any any other larger capacity fuel tank.
  17. Transalp
    I have a 700 Transalp and would like it to rev less in top gear, should I put a larger front sprocket on or a smaller back sprocket, what are the pros and cons ?
  18. XR
    Can anyone help with the numbers for the top and bottom steering bearing on a 2002 XR400? I see mentioned around the net and ebay both E32005J (25x47x15) and E32005/26 the latter being 1mm larger on the ID (26x47x15) So which do I need?
1-19 of 36 Results
Top