longer

Hi - does anyone have SW motech pannier frames they no longer require - for the trax - Givi Kapper the quickly detachable type thanks - Pat

Hi Everyone. I'm looking for a battery securing strap, no longer available from Honda. any suggestions? thanks rich

now Avon Gripsters are no longer available I am considering replacing the rear with a Mitas MC24 ( I have them on the TA600) or E-08 (cheaper than MC24 & bit more road orientated). I only use the TA650 on the road or gravel but many local roads are poorly surfaced and often quite muddy. There...

Hi all, (newbie) , just done a post on the crf page but think posting here may get more response, iv recently purchesed a 2014 crf 450r, on adjusting the chain I found a seized adjuster and yes like a t**t I snapped it trying to undo, iv tried several metal drill bits to drill out without...

Hi all, iv recently purchesed a 2014 crf 450r, on adjusting the chain I found a seized adjuster and yes like a t**t I snapped it trying to undo, iv tried several metal drill bits to drill out without success, my question is can anyone recommend a drill bit that will get through the snapped...

Anyone chopping up their bike and no longer need the left side switchgear? My indicator switch has just snapped inside and could do with a replacement. Thanks!

Has anyone out there got an un-wanted centre stand for a 600 Alp (mines a '98 model, but earlier ones should fit)? Checked with that excellent source of new Honda parts, David Silvers, and apparently the stand is no longer available. The after market availability of a stand is very patchy as...

I am looking for a "do it all" bike, to replace the Transalp (London ULEZ has kiboshed it's use) and the R1200RT. I am looking at the Vstrom 650, the Tracer 700 or the NC750X I have ridden the NC750X recently and it was good. I rode the VStrom a while back, but can't remember anything about...

Hi i was just wondering if anyone knew what length chain i would put on my Re-build. I have put an AT swingers onto an 87 Transalp frame, I think the AT had a longer chain than the TA due to the longer swingarm but no sure about this combo...

Has any one got a pilot jet for a carb fitted to a RD02 to hand, or happen to know the length? Just stripping the carb and the current pilot jet that was fitted is 24mm in long, however the refurb kit for the carb came with one that was 28mm long. Any clues on which one is correct? The 24mm...

On longer rides, especially when loaded up, I find that my arms sometimes start acheing. I'm thinking of trying some higher bars. Any recommendations and do they affect the handling etc of the bike? Also what if any modifications will be needed to the controls etc? Thanks for any answers. Nick...

Have just discovered that the spacers within the rear linkage are no longer available. Two of mine were completely seized, the smaller one where the shock attaches is available from Honda but neither of the longer ones are. Has anyone found a similar part that will fit or could be modified...

Hello from Greece,Im rebuilding my XL600LM (1985-PD04) and i need the GUIDE, CAM CHAIN Part number:14620MK4620 which replaces (14620MG3003, 14620MK4600, 14620MK4601 that older XRs have). The problem is that this part, is no longer available!!!Has anyone tried the NX650 ? i.e.(14620MN9870 Guide...

Just tried to post and lost the thread, here goes the second attempt. Have some good parts to go on Can this be cleaned up in the frame? I really want to keep the engine in the frame. Go gentle on me. I'm no expert, basic tools, small space to work in and a tight budget...

I have 25mm handlebar risers on my @ and have just fitted starbars. Thing is, the bars are a tad longer than standard bars and on full lock the engine revs due to the length of the throttle cables not being enough. I like the new bars and also like the risers, so is there a longer throttle cable...

The collars of the linkage are no more available. I need the 17.5 x 12 x 61 mm, code 52463Ms8000 Does anyone has an idea where I can get one or something longer that I can use?

You know that moment when you poke something with a screwdriver and immediately wish you hadn’t... I found a bit of flaky paint around where the seat and silencer bolt to the subframe, off side. One poke with a screwdriver later, I had a hole. After a friend attacked the affected area with a...

Hey all, My clutch cable snapped last week (luckily once I was home and parked) and I just swapped it out the other day. It took me longer than expected to free the old cable, purely because there was a little cable clip on the rear of the main upright. Difficult to see or feel, but once I had...

Is there any clutch cable that has the same ends as the stock cable but longer to fit a RD03? I herd that the RD07 might be the same but longer ? Traveling The World Two Up on a 1989 Africa Twin 650. Updates Here: www.instagram.com/Africa.Twin.Adventures www.facebook.com/DHealy91

Hello. Please PM me if you have an unwanted reinforced Stefter sprocket for an XRV750 that you no longer need. Thank you!