Honda XRV Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 195 Results
  1. Member Classifieds
    I am in search of the lower exhaust heat shield for my ‘89 RD03, anyone has one laying around?
  2. XR
    Being a vertically challenged 5’7 90kg with 30” inside leg I might need to lower my (new to me)Xr400r a tad! ive bought a second hand seat and will be sending it off to get the foam shaved down a bit and a new seat cover but think it might not be enough! Was considering a lowering link but it...
  3. Africa Twin
    Hi All Has anybody got a heat shield for AT RD 07, the lower one that fits between the down pipes and the tail pipe, mines a bit battered and not happy with it, paint finish not an issue but must be quite straight and undamaged. Thanks Luke
  4. Transalp
    Hi new to this forum, and suffering from ducks disease i want to lower my 650 ta been told sv650 curvy rear shock will fit,and is 10 mm shorter, any confirm od debunk this please.
  5. Africa Twin
    Has anyone here replaced their steering head bearings? If so...how did you remove the bearing 'race' that is on the lower yoke? This thing... The internet suggests - using a chisel - using an angle grinder - using a dremel - using two screwdrivers - using some sort of special tool so...how...
  6. Transalp
    Has anyone here replaced their steering head bearings? If so...how did you remove the bearing 'race' that is on the lower yoke? This thing... The internet suggests - using a chisel - using an angle grinder - using a dremel - using two screwdrivers - using some sort of special tool so...how...
  7. Africa Twin
    I'm looking for some help on the mounting of the chain slider. I've been working on a restoration and it has been some time since I've been at it due to health reasons. When I went to put the slider on, the mounting point does not seem to be right. I'm wondering if one of the points has been...
  8. Member Classifieds
    I am in need of a white front fender for my 1993 RD07. If anyone has one in decent condition that they would sell, please contact me. It is one of the last pieces I need for my complete rebuild I am doing. I already have brand new white plastic lower fork leg covers, so I just need the...
  9. CRF - New Forum!
    Had my crf 450x stolen last night , if you are going to look at any for sale in the future mine had a few one of marks, deep scratch on the frame near the weld on the left side , one off led headlight, home made stand headlight board had been repaired the a blue plastic piece to hold it to the...
  10. Transalp
    Well, I’m back! First post for over two years. Been away from Honda, big mistake. Let me just say that Transalps are superb. Oh, a pain to work on the engine but..... :D Picked up Suki yesterday, a new to me 09 plate. Ahhhh, lovely ride. Anyway, back to tech... The rear brake pedal is 8 feet...
  11. Transalp
    TA 650 (probably applies to all models though) For anyone thinking of doing this..on the 650 its a bit of a job. The Haynes manual says you just "attach the lower end of the new cable to the upper end of the old cable, and just pull the cable through", yeah, right. What it fails to mention...
  12. XR
    Hi All, I've just recently aquired an 93' XR650L and it didn't run well initially. Symptoms where popping once in a while while driving, but also when standing still, dropping gas to idle, it ran for around 15 secs and then one pop in the exhaust and boom stop :-) I reckoned it was running to...
  13. Africa Twin
    Does anyone know how to remove the lower triple clamp from a set of ktm 950 forks? I have the bearings off but the steering tube is stuck solid and my finger cant't take another whack with the lump hammer. Also when I get this off how do I fit the adaptor back in? Thanks
  14. Member Classifieds
    Part number is 45210-MY1-006 or 45210-MAY-006 for XRV750 1999. I believe the same part is on the Transalps. This is the black plate that mounts the Left caliper to the fork leg. Like a complete idiot, I rode off with my disc lock still on, which broke the lower part of the plate when it made...
  15. Transalp
    Hi i tried this today, Im not sure if it works on the road but it sits almost the same as my AT did. I fitted the swingarm from my 2000 AT onto my XL600v frame, The AT shock was too long but i tried the shock from a 650 TA and it slid straight in. It does look slightly lower than a pic of an AT...
  16. Transalp
    I was reading a ridiculously long thread on a Harley forum all about front suspension (as one does) and much was said about setting sag, after installing bespoke springs...as far as I'm aware, my 94/5' 600 has the long fork springs installed, ie there are no spacers between the spring tops and...
  17. Transalp
    I was reading a ridiculously long thread on a Harley forum all about front suspension (as one does) and much was said about setting sag, after installing bespoke springs...as far as I'm aware, my 954/5' 600 has the long fork springs installed, ie there are no spacers between the spring tops and...
  18. Member Classifieds
    I’m after a standard or higher seat. Can buy or swap for my Corbin lower seat.
  19. Other Bikes
    Hi, would really appreciate your help with my 2004 Honda CB1300 My bike clocks started playing up and stopped working. bike starts all good and all led lights on the clocks work but not the speedo , tacho , digital display and digital clock.Normally when you turn the ignition on , everything...
1-20 of 195 Results
Top