Honda XRV Forum banner

nut

  1. Africa Twin
    Hi i have two part numbers which i cant conclusivley identify ? both should be for the front cowl / fairing . 90111-mm9-000 and 90156-se3-003 What i need is to replace the perished rubber bungs which combine the nut internally i think its a 5mm nut(could be wrong) I have 12 screws holding the...
  2. Chatter
    Had a great weekend at Dirtquake which takes place at the Adrian Flux arena in Kings Lynn, loads of nutters on everything from scooters to 1100 sports bikes and choppers racing around a speedway track, few serious racers having a go too , Guy Martin, Carl Foggarty, Steve Plater, Gary Johnston...
  3. Africa Twin
    Mine is siezed good and proper, at the end that bolts to the frame. It is going to need attacking with extreme prejudice, but before I get the really big hammer out, I need to know if the bolt that attaches the link to the frame is held in place just by the nut on the bolt, or alternatively it...
  4. Varadero
    I was adjusting the headlight on my 125 varadero (XL125V 2005) and the adjuster screw has wound out of the internal nut. Is the headlight a sealed unit? if i take it off will i be able to open it up and re-attach the spring and screw. At the moment the headlight is shining at my front mudguard...
  5. Chatter
    I finally ordered the seat for my dommie project. The bike is at the electricians place awaiting completion and should be ready within the next week or so.:thumbup: I have ordered the top left hand seat and I have chosen chestnut as the colour:D:D:D This bike is going to be the dogs wotsits...
  6. Dominator / FMX
    Hi Guys, Can any one confirm the following for me please: Honda NX 650 front disc, what are the nut sizes? I think 14mm but the spanner seems a bit lose so want to double check. I have only tried one of the nuts and it already feels like its going to round off. I also tried to loosen the...
  7. Africa Twin
    hi anyone has a spare pressure plate ... broke it!!! . also have an fzr 1000 exup and the nut torques at 90nm and it has mutch more power... why the hell does this engine needs 130nm??? and that loking tool is a hell to get or fabricate!
  8. Transalp
    Hi, been replacing my friction plate's and spring's on my v2 TA and had to get a fresh clutch nut, the old one had a stake in it but the new one doesn't. Did they change the nut for a stake less one or is it the wrong one?
  9. Dominator / FMX
    Just fitted these onto my dommie but I have a piece left over and I dont know where it goes, any ideas chaps? The boxes are just resting on the angle aluminium and held on with a bolt with wing nut but they are not very stable, does anyone know what the bracket is for in the middle photo?
  10. Chatter
    Any one else watch this programme? Absolute nutters and there is only one outcome doing that sort of stuff! :shock:
  11. Dominator / FMX
    The Dominator is fighting me at every turn! :( Now two of the exhaust studs have broken off leaving about 1cm clear of the head - actually everything exposed beyond the nut just crumbled away at the slightest touch. Not sure what to do next as there is not enough clear to even contemplate...
  12. Africa Twin
    Hi I'm trying to adjust the preload on my RD07 rear shock and having bother moving the castle nut at the top. I know it's probably a stupid question but before I do any damage.........................it is anti clockwise to loosen this nut isn't it ? Cheers
  13. Africa Twin
    Morning peeps. I just wondered if anybody has the reverse thread nut for the right hand mirror. I broke my mirror in Greece, I'm in the UK and the bikes still there. I've bought an eBay mirror but its missing the nut. Help Rob Aim for the Horizon | Ride the World
  14. National Meets
    Thanks to Mudwiz and Ralph for joining me on a trail ride last Saturday. Me and Ralph on suitable big trail bikes, 950 SE and XRV750.......and Mad Mudwiz on a completely unsuitable "Road Bike", Vara 1000 with K60's. Nutter. Photos are better than words any day. Enjoy.
  15. Africa Twin
    Hi all, I've encountered a strange problem lately. I notice that when I'm cruising around town and I pull to around 100 km/h, release the throttle, my speedo needle won't react or very little at all. Then, when I pull the clutchlever, rev the engine up, the needle falls to around the speed I'm...
  16. Africa Twin
    Had an abba stand in the garage & no centre stand on the bike. Rang Abba & they confirmed that they don't do a kit for the @. However, I bought 22mm & 17mm swingarm nut adaptors for the stand off them just to try & see if it would work, & low & behold it works fine :) Rear wheel ends up...
  17. Africa Twin
    Sun - check Bike - check Helmet - check Tax - check MOT - CHEEEEEECK!!!!!!!! IT passed - woohoooo!!!! Beware - big black AT with loose nut at controls!
  18. Chatter
    now i know lings could probably get you any part, & their (newly modded to access/acsess)...website is a wealth of lots useful information, as well as their employees........but £773 + P&P for an @ starter motor !!!! good job it was just a matter of tightening the +tive nut & there's a spare...
  19. For Sale / Wanted
    Trying to sort out a fellow AT enthusiast from foreign shores who I will shortly be sending some parts to who is after the following: Top steering stem nut 90304-415-000 Washer 90503-283-000 Castle nut 53229-KN5-650 Think these are the same on all the models. Cheers
  20. Africa Twin
    Hi there, to prepare for the next steering head bearing change, I´d like to get myself a castle nut wrench to correctly torque the toothed steering stem nut. Does anyone have the required diameter of the wrench in millimeters available - I would prefer not to disassemble my bike at this time...
Top