ordered

Last time I fitted a mosfet I got wiring kit from eastern beaver and with handling fees cost nearly fifty quid. This time I have ordered the fittings from uk but I need some advice on the battery to mosfet wiring size, this is what I was going to buy but would like someone with more knowledge to...

So the weekend was supposed to be a wife free bike stripping and rough tickover solving couple of days with maybe a cheeky ride out or two. All started well other than an exhaust valve inspection cap trying to break while being removed but I managed to remove it with only minor damage. The...

Sorry folks, I'm asking for help again. I'm going to hopefully be cleaning and stripping the carb this weekend and while its out i will be replacing parts as i go. Does anyone know the sizes of the carb manifold clamps for both the air filter and inlet manifold rubbers? I would try and...

This might not interest anyone, except those with some spare Nonfango panniers. It might not interest them either, but hey! :D Just received my newly ordered Givi pannier brackets for my new to me 700. as I had the nonfango panniers, the made up brackets as well and these were last fitted to my...

hi all i returned from a ride and noticed coolant coming out of small hole under water pump - i ordered some replacement seals but it has made no difference is this fixable or has the shaft worn so therefore a good seal impossible its a 35,000 miler 2001 model 650 TA i have priced a replacement...

Hello,my neighbour has a XL125 varadero think it is 2004/05 when you go to start the bike there is just a single click it does not repeat just one click coming from around the fuse box area, he bump starts the bike and it runs fine,he also says that sometimes it does start,he has ordered a new...

Just a heads up folks on this new gadget ive got to play with ... its a real time tracker £35 of fleabay .... ive got it for my van but can use it on bikes cars ect ect ... i did a bit of reading before i got it and there was mixed reports but for the money i took a punt...

So a while back one morning she failed to start, ignition dead. I traced this to the starter relay, and it was fairly well melted as is well documented - a bit of a wiggle and she came to life. So I ordered the new relay, which came - and now Ive fitted it I've run into issues and she wont...

After taking my calliper apart to clean the pistons and bores and to replace the seals I made the error of not taking photos of where the two clips/shims go !! I've ordered a manual but until it comes can anybody help? It's a twin piston calliper off a '93 transalp and there are two stainless...

Hi I have recently bought a very cheap 1989 RD03. It had been stolen, and was written of by the insurance company. The thieves have painted it flat black, and broken some parts. Luckily the black paint comes of quite easily, without damaging the original paint or decals, but I'm having...

Was doing a routine check and found that the front axle holder was broken and the nuts on the studs were so loose that they could come off by hand. Anyway as I do not have torque wrench I managed to snap 1 stud off and then was trying to put a temporary support plate which caused the other stud...

Has anyone tried out the kk bike sprokets? I think they look pretty good If you want to avoid shaft wear. https://kkbike.it/en/120-sprockets If not I just ordered a superpinion and will report back in about 2 years.

I just ordered this : DUHAN Autumn Winter Motorcycle Jacket Men Motocross Equipment Cotton Lined Cold-proof Motorbike Moto Jacket Protective Gear A friend of mine got it and I love it so I ordered mine. Sent from my MI 5 using Tapatalk

I finally ordered and recieved my new Arrow PD exhaust. Looking forward to getting it installed but Curious about what I call exhaust tape that is very similar to putty sort of. Does anyone use it over here? I notice a lot of folks using exhaust paste but that looks to be a messy setup. Any...

Hi Folks Got a rattle going on somewhere on my RD04. I've ordered some new bash plate rubbers / collars etc and when they come I'll remove the bash plate as I know that seems to be the most common cause of noises. Today I was giving my chain a clean and lube, and in the process was pushing...

I currently have a 1990 ish motor (without kickstart) that is in need of a rebuild. I have found a good 1988 motor.I believe the early motors had different splines on the gearbox shaft. I am asking because I currently have a 14 tooth sprocket fitted because the motor is in a sidecar that I...

I stupidly ordered a Cyclops H4 LED bulb (with rectifier/regulator) for my US model XR400 headlight and of course I can't mount it in the stock light assembly. Is there another XR headlight assembly (AU version?) that will accept H4 bulbs or an aftermarket option? Thanks! Here's the bulb...

Just a heads up. I've just ordered a brand new centre stand for the 650 Transalp, £85 shipped from Germany. It seemed to be a decent price, if anyone is looking for one. Sent from my SM-A320FL using Tapatalk

Does anyone know the size of hose used on the front and rear brake reservoirs. I need to replace hose that's between reservoir and master cylinder. (front and rear brakes). Would measure it, but want to get some ordered asap. Bike is an RD08

Hey guys, I came out of work a couple of weeks ago and noticed loads of plastic bits around my bike. Apparently someone knocked it over and in the process took out my R/H side indicators. Anyway, I ordered some replacement indicators, to get to the front indicator properly, I wanted to remove...