Any opinions on the speedometer overlays I have seen? I’m back in states with rd07a and would like to change speedo over to mph now from kph . This is a lot cheaper option versus full speedo replace. How hard if someone has done
Looking to replace all the fuel lines on my RD03 as a couple more leaking a bit nowadays. Rugged roads has 4or5 sizes. What is most common I would need? I plan on buying some bulk lengths. They have 4.5, 5.5, 7.3 and 8mm ID. Mine are so old going to be hard to determine sizes. I know I have used...
I would like to replace my coolant hoses on my RD03. Honda parts are NLA. I was reviewing threads about the Samco or other aftermarket hoses and found threads that stated that some hoses were incorrectly sized.
Those hose kits are pretty dear. Can't see paying that much for parts that are...
My tranny just died while out in spain, the con rod snapped appaently!
I have my eye on a 1996 PD06 engine to replace the old one. I hear that the 1996 engines had a "new whole electronic (TCI) ignition system (new ignition unit, new impulse ignition coils, new ignition advance...
So I bought a well used ‘89 XRV650 which I am rebuilding. The weels are corroded and I need to replace them. I’d like to keep the bike as original as possible so I’m looking to source original DID rims.
I allready found a nice used rear wheel and now I’m searching for a front wheel rim (I will...
Hello, i notice one of my grommet's is missing and I would like to replace it
Looking at the Honda diagrams they seem to be coming up as Air Cleaner Case Grommet's and the part nr is 83551-300-000
Can anyone confirm
Hello, I was changing my main air filter over the weekend and decided to have a look at the "sub filter" too. part nr 17259-MCB-610, it pretty much disintegrated when i was cleaning it....
so have two question's
what does it do (i like to know these things)
what can I replace it with, as there...
I am trying to get a severely corroded RD04 running, The carbs have completely seized and it appears to be due to external corrosion. Is there a good resource available to understand...
I am in the middle of deciding whether to replace an output shaft on the AT, XRV750 - 2002.
Can anyone give me a list of the parts I need to order, gaskets etc to do this job? - gonna use the VT750 shaft.
Also is there anything else worth doing whilst I have the engine in pieces?
I just made myself one of these sleeves out of stainless steel for the rear caliper on a 96 RD08 (part No14 in the link below) hoping i'll never have to replace it again. Its a cheep enough part but i wanted an excuse to use the grooving tool i bought :D
I made two so have one spare if anyone is...
My nx650 RD02 (1989) is in need of a new shock. The current shock is an old Hagon that is at least 20 years old fitted by the previous owner and I doubt very much it is serviceable by the look of it.
Im on a tight budget (meaning I don’t want to spend a fortune) but need to replace it...
Hi All. Long time no post. I do hope you're all well.
My rear shock is getting a bit long in the tooth and I want to start looking to replace it. My bike is 100% road going these days so I would not be against a road set up rear shock, so does anyone know what fits? I know there are lots of...
OK so I'm on a roll now asking questions!
Bike warms up lovely when stationary, temperature gauge showing where it should be however, as soon as I start riding gauge drops to zero.
I'm guessing that either
a/ Thermostat knackered
b/ Thermostat doesn't exist.
If either a or b I need to replace...
I'm thinking of buying a YSS to replace the very tired original shock.
I bought one for my 750AT and it jacked the rear up by 3". Nice shock but the seat is high now.
Is the Transalp YSS the same deal ?
I am looking for a "do it all" bike, to replace the Transalp (London ULEZ has kiboshed it's use) and the R1200RT.
I am looking at the Vstrom 650, the Tracer 700 or the NC750X
I have ridden the NC750X recently and it was good. I rode the VStrom a while back, but can't remember anything about...
Hello guys ,
i was just wondering if anyone tried to replace the rear shock from another model Honda/Yamaha..etc ?
the aftermarket is too expensive and new OEM as well . i see a lot of good rear shocks in good condition and cheap as well from other bikes
any idea ?
Got my hands on a gratis Garmin Zumo 396LMT-S Motorcycle GPS, so decided to replace the TripMaster (which on mine was still fully functioning!)
Anyway, I used my 3D printer to make up a bracket to mount the Garmin on the original tripmaster mounts. I have the 3D models if anyone wants to...