Honda XRV Forum banner


  1. Standard carb clamp sizes

    Dominator / FMX
    Sorry folks, I'm asking for help again. I'm going to hopefully be cleaning and stripping the carb this weekend and while its out i will be replacing parts as i go. Does anyone know the sizes of the carb manifold clamps for both the air filter and inlet manifold rubbers? I would try and...
  2. Wanted: Wanted - RD04 nuts, bolts, rear wheel spacers, carb to airbox rubbers.

    For Sale / Wanted
    During our move a box has been misplaced :( Now I have time, space and money to start this rebuild. A lot of xrv rd04 have been broken for parts but no one seams to keep the little things ! Pricing these small items new, very expensive. Thank you. Safe Riding.
  3. New Carb Rubbers....Supplier?

    Africa Twin
    Hi, I have discovered that one of the above items has a small tear in it, so I intend replacing both. I cannot seem to find a supplier, Honda Part no; 16111-MY1-000 states that it covers up to year 2000, mine is 2001. Any ideas as to suppliers of new genuine replacements? Thanks, Pat.
  4. footrest rubbers interchangeable

    Africa Twin
    Can the rear footrest rubbers be used on the front footrests? cant quite tell and cant be bothered taking them off to check :-)
  5. For Sale: RD07a USED & NEW PARTS Look Into

    For Sale / Wanted
    I have to make some room in my cellar. Just collecting all the time. But now its time to sell some stuff: Front Lights Left Side Panel 1996 (NEW, never used, OEM, original package) Front & Side Panels (Used, somewhere broken but good as spare, Fully Functional) 2X Rear MudGuard (not clean...
  6. Side panel 'grommets' missing?

    Africa Twin
    Hi Folks Got a rattle going on somewhere on my RD04. I've ordered some new bash plate rubbers / collars etc and when they come I'll remove the bash plate as I know that seems to be the most common cause of noises. Today I was giving my chain a clean and lube, and in the process was pushing...
  7. RD07A Airbox fitting problem

    Africa Twin
    Hi Managed to get a few hours in the man cave before the big day and had issues fitting the OEM airbox on my RD07A. As noted by others the connecting rubbers from airbox to carb inlets can shorten with heat and fuel. The result is they are now too short :( These are the rubbers from another...
  8. XR250S Metal Tank

    Hi, Does anyone have an XR250s metal tank for sale (around 1996)? its an MD30 and has the single bolt at the back of the tank to fix and two grooves on the inside of the tank that slide onto rubbers attached on the frame. Part number 17520KCZ000ZA If not - is there any other tank that fits -...
  9. Pillion foot peg rubbers

    Dominator / FMX
    Pillion foot peg rubbers on my Dommie are perishing and falling apart, currently held on with cable ties. Despite the fact I NEVER take a pillion, this has been bugging me so I bought new ones from David Silver. Does anyone have experience/ top tips for replacing those? It looks like it...
  10. Handlebar rubber mounts, can they be replaced?

    Dominator / FMX
    Hi everyone. I have a 96 Dommie that I use for all sorts of travel on and off road. I noticed recently that the bars are moving more in the rubber mounts. Can the rubbers be removed and replaced? I tried tightening the nuts under the top yoke but still they seem to wobble more than before. I...
  11. RD07A squeaking noise - load dependent

    Africa Twin
    I have noticed a faint squeaking sound coming from my bike. It sounds like it's from the front sprocket area but of course could be anywhere. At higher speeds wind noise totally covers it. It is 'in time' with the power pulses from the engine but disappears if the clutch is pulled in and...
  12. I need rubbers

    Africa Twin
    Now that I have your attention. Having finished refurb'ing my carbs I need to put everything back together. However, Honda are no longer making the two front filter box too carb rubbers, so original units are out, which leaves me with a dilemma! Are there any aftermarket suppliers for these...
  13. Service stalled......

    Got the service kit this morning so set about the bike ready to get it done. Took the right fairing off only to find this.... need to buy a new set as the other side is very badly rusted and barley makes a connection. Then noticed the rubbers mounts for the fairings are all kaput...
  14. Carb inlet Rubbers

    Africa Twin
    Hi, Just got myself a RD04 which is restricted by the inlet rubbers. Is there an easy and hard way of replacing them ? Cheers Bob.
  15. Ok now Cush drive rubbers on the way out

    This morning in Georgia I did the chain and my friend took her for a spin. There is no garage able to take the rear wheel off and wrap them. Wondering what my best course of action is? No man is truly married until he understands every word his wife is NOT saying.
  16. Wemoto carb rubbers

    Africa Twin
    Anyone used these? With the cylinder head locating tab in the correct postion they don't seem to allow the clamp/clip with the tab to line up properly. It ends up fouling on the valve cover and slanting diagonally across the rubber. There are two different clamps and I have them installed the...
  17. swiss RD03

    Africa Twin
    swiss RD03 (now with photos) it turns out that the 03 i'm possibly looking at on monday is a swiss model with square lights.i remember searching on this forum that they are restricted (?) at the carb rubbers. its low mileage 32k kms, unused for 8 yrs,probably cant hear it running unless i...

    Africa Twin
    I'm so pissed off today, just received a letter from Honda France informing me that my @ (ex 621Andy and my first @ ) which was originally from Germany but now UK plated, can't be registered in France because it is...
  19. This company scrapped this bike

    Africa Twin
    I dont understand why you would break this bike I would think its worth £2500 as is LOOK HONDA XRV750 XRV 750 AFRICA TWIN 1990 INLET STUBS RUBBERS *FREE UK POST* | eBay Can anybody enlighten me as it would take months to sell it all to get that amount?
  20. Footpeg rubbers - good or not so? Do you have the same pegs...

    Hi all, Kind of thought I should get some footpeg rubbers to reduce the vibrations, i dont think these are original Alp footpegs- - can anyone tell? And there seems to be a screw hole in the centre to add the rubbers, any thoughts? I cant see a brand name on the pegs, so makes life tricky to...