Im Looking for tank badges/logo for my CG125 tank. The spacing between screw mounting holes is 60mm, but all the badges i can find on fleabay are 67mm spacing between holes. Anyone bought any of these in the past for their CG125 tank with 60mm hole spacing?

Im Looking for tank badges/logo for my CG125 tank. The spacing between screw mounting holes is 60mm, but all the badges i can find on fleabay are 67mm spacing between holes. Anyone bought any of these in the past for their CG125 tank with 60mm hole spacing?

Hi there, I have a 99' fx650 which I purchased to refurb and modify. I do not know how it ran before it was dismantled. It was only started. I have now rebuilt after refurb and I'm having trouble with engine hesitation with throttle open. I have put a larger main jet (175) as it has a custom...

Hi. Dose Any one have a workshop manual that can tell me the base carb settings. Float hights And fuel mixture screw settings Many thanks Sent from my SM-G955F using Tapatalk

When i bought my 89 nx i noticed the idle screw cable was snapped off at the carb, the tosser i bought it off assured me he had a spare and would send it on. Well he didn't and i have no way of adjusting as the cable has snapped tight up to the point of entry, CSNL have none nor D S. does anyone...

Hi, Please would somebody give me an advice on changing the exhaust downpipes? I'm always worried I may shear off the lugs that screw into the cylinder heads when I'm undoing the domed nuts holding the flanges. Also, is there a work around to not having the gasket between the downpipe and the...

Hi guys I'm Marco from Belgium. I have an RD04 from 1990. It's a great bike, but has had some bad owners that didn't maintain it. :( I have replaced the rubber inlet seals, valve cover seals, fuel hoses, blablabla... =) Now i am left with one part: a screw, a tiny washer and something on...

Hi before holiday in Italy I play with air/fuel screw as I thought it's running to lean and overheat to much. Unscrew half turn more. During ride when trying to drive more then 65 miles engine start losing power (the jumping feelin, like no petrol)) I changed setting back what had before (more...

Hi All, Complete new Dominator owner here so bear with me. So I thought I'd check the oil today but ended up a little confused. The dipstick has a thermometer on it as you can see from the attached pics. But it doesn't have any markings on the stick to say high or low oil level. So any...

Assume gear lever was worn, purchased new one, shaft also worn :( would it be ok to weld for now? I assume it's engine out and strip etc ? Any other ideas ? Could I drill through pedal and shaft tap it then add grub screw ? What options do I have Tia Sent from my iPhone using Tapatalk

What do you guys use to undo the drain screw on the float bowl, only all my screwdrivers won't fit even the small ones, too little space, any advice please

ihave replaced one seized piston all pistons push in with two screw drivers quite easy. also have replaced hoses with braided hoses. brakes are spongy and no braking power. you would be afraid to ride this bike. if i leave lever held in for a few hours lever becomes better. but then after a...

HI i LAID MY DOMINATOR UP FOR THE WINTER AND NOW IT WON'T START. BATTERY HAS BEEN ON A TRICKLE CHARGER . CHECKED THE SPARK AND SEEMS OK. WHEN I LOOSEN THE DRAIN SCREW NOTHING COMES OUT. WHAT DO I DO NEXT? THANKS PHIL.

I have just finished fitting my nice clean carb nice job i thought put it on the bike ,start,full choke bike fires up no problem , wait a couple of minutes ease of choke ,bike back fires . pull choke to on position bike revs freely THEN:mumum::mumum: Down pipes glow cherry red...

Hi there, I'm a French guy and this is my first post here (and also first time opening a Domi engine) because I wanted to change the cam chain for a friend's Domi and one screw maintening the chain tensioner broke while trying to take it off :eek: I've tried all the ways to take it off from...

I was adjusting the headlight on my 125 varadero (XL125V 2005) and the adjuster screw has wound out of the internal nut. Is the headlight a sealed unit? if i take it off will i be able to open it up and re-attach the spring and screw. At the moment the headlight is shining at my front mudguard...

Howdo, I'm new to biking. Passed my test in June this year, I'm 40 mid life crisis etc. Anyway I bought myself a spangly GSXF650f its great but after some browsing for a 'winter' bike I set my heart on a Dominator. I bought one this week but have a few questions if I may? Id like to fit some...

Hi all, If the answer is yes can you please have a look at your service manual (the one which honda supplied ) and let me know the initial setting and final setting of the mixture /pilot screw. I think it's on page 5-18. Thanks.

Hi all, Does anyone know if a carb from a 125 Shadow will fit a 125 Varadero? As I can't get a Varadero from any where. I have checked part nos and shadow is 16102-kgb-d11 and Varadero is 16102=kpc-d21. The only difference in looking at them is the idle screw. Thanks.