Honda XRV Forum banner

se

  1. Dominator / FMX
    Looking for recommendations on the best / most effective brake pads, with standard RD02 setup please Thanks
  2. Dominator / FMX
    Hi all. I’m building a scrambler / flat tracker from my FMX 650. My standard carb has two sets of electrical connections on it. What are these electrical connections for, what do they do??? I have a Keihen FCR flatslide carb to go on the bike when I’m finished the build but this carb doesn’t...
  3. Africa Twin
    Hi! I have this Africa Twin RD07 a -98 model. I bought it like 3 years a go and it had the knocking sound from then. I have replaced the cam chain tensioner and exhaust gaskets. Non off this did help. The sound is only there when driving when the engine get some resistance. When standing...
  4. Africa Twin
    Can anyone recommend somewhere to send all my bolts to for zinc plating and my bits of chrome pipe for chroming? Local places just are not getting back to me and Ashford chroming quoted £384!! Thanks
  5. Dominator / FMX
    Hi. Can anyone point me in the right direction to find a replacement set of swing arm bearings to the Honda FMX. Genuine Honda one seem to be discontinued and are very very expensive. Are there any pattern parts out there ? Thanks. Jez
  6. Transalp
    Hello all, What is you experience after the decat, do you get blue header pipes colors? Did runs the bike not more the 20in without the O2 sensor elinator, could that be the reason? With the lambda/O2 sensor, would the blue coloring stop? Cheers Mike
  7. Africa Twin
    My AT has a set of bars on that are too short for the handgrips(a cheap quick replacement by the previous owner). I have the originals but they are slightly bent, so rather than powder coating them, I was lookig at the Renthal Enduro high bars. Question is...will the original bar ends and...
  8. Dominator / FMX
    Set to with the debaffle today. Cut the end off the two baffles so I could get 38mm hole saw in. Cut the baffle out and then welded a 42mm piece of pipe onto the hole so it looks a bit tidier. Gave it all a blast with some black vht paint and she sounds like a good un. Just got to swap the main...
  9. Africa Twin
    My current sprocket setup is -1 front and +3 in the rear. I like this, but I'd like to get better mileage on the road and I want an OEM 16T front for reduced wear on the shaft. Thinking of changing my chain and go to just +1 in the rear or should I go with the stock 46 tooth rear sprocket?
  10. Transalp
    Have a newly acquired 2008 700. Does anyone know the factory settings for damping and preload on a std shock? Its fine over big bumps (like speed humps) but a small, frequent sequence (like when the tarmac gets ripples in it - or rumble strips) feels like there's no suspension at all. I'm...
  11. Africa Twin
    Hi All, I am trying to build up a new set of wheels for my RD07A so I have the old ones and a set of new. The reason being the old set will have road tires and the new set will have 50/50 tires on for an easy swap around when I want to hit the Bush down here in Melbourne and my new wheels will...
  12. Transalp
    Hi, as the title says - where is the crank position sensor plug ? - on a 650 it's under the tank on the left side, but what about on a 700 ? cheers
  13. Africa Twin
    Took delivery of my new bike camera yesterday, It has two cameras , pic capture , video , collision sensor , HD and was only £30.. Tested it out and the quality is pretty good, Takes a micro SD up to 32GB, does rolling carture and has low light mode
  14. Africa Twin
    Do they fit over the existing plastic protection for radiator or do I remove them? Just curious before I start putting them on tomorrow. I have a set of aluminum guards handy but I was going to ship them to the states for my RD03. I'll keep them here if they are needed. Thanks
  15. Dominator / FMX
    Gents, Im sure this has been done before; can you give me sign posting to instructions for fuel tank removal (and/or workshop manual) as want to send it away to Dream Machine for Rothmans paint job :) thanks kimosabby
  16. Transalp
    Everything you need if you have lost all the keys to your 650! £150 posted (uk)
  17. Bodgers Corner
    I'm working on a project with my VTR Firestorm getting some stainless steel split flanges fabricated in a small run. On the VTR v-twin the front pot gets hit by salty spray and heat and the OEM mild steel flange gradually disintergrates. Not helped that Honda set them as non removeable on the...
  18. XR
    Got a xr400 oil cooler off my Dominator flattracker just the oil cooler no connections FOR SALE sensible offers
  19. Africa Twin
    Hi i have two part numbers which i cant conclusivley identify ? both should be for the front cowl / fairing . 90111-mm9-000 and 90156-se3-003 What i need is to replace the perished rubber bungs which combine the nut internally i think its a 5mm nut(could be wrong) I have 12 screws holding the...
Top