Started to change the output shaft on my 700 XL.
All the bolts holding the chrome heat shields and the painted heat shields were sized in so that took me around 4 hours to do,
I’m a slow worker, drill out re-tap the holes and order new bolts.
The rest went as I expected it to no real drama...
hi i have an XR400 standard bike, i live in portugal and parts are hard to get, i am looking for piston ring set and top half gasket set with valve seals any idea where to get them in uk thanks kevin.:cool:
Hi All. Long time no post. I do hope you're all well.
My rear shock is getting a bit long in the tooth and I want to start looking to replace it. My bike is 100% road going these days so I would not be against a road set up rear shock, so does anyone know what fits? I know there are lots of...
Hello all !
This winter i want to rebuild my beloved AT as it already eats some oil - about 1l/1000km or so.
I bought 8 years ago an complete engine with about 35.000 km, or so the seller told me. Anyway, i kept this engine in storage for 8 years and before i`ll put it on my bike i wanted to...
i returned from a ride and noticed coolant coming out of small hole under water pump - i ordered some replacement seals but it has made no difference
is this fixable or has the shaft worn so therefore a good seal impossible
its a 35,000 miler 2001 model 650 TA
i have priced a replacement...
Does anyone know the dimensions or numbers of front and rear bearings and seals ?
I want to put some in my spares box before a trip and can normally source them through work :)
List from lings site to help future readers
After taking my calliper apart to clean the pistons and bores and to replace the seals I made the error of not taking photos of where the two clips/shims go !! I've ordered a manual but until it comes can anybody help? It's a twin piston calliper off a '93 transalp and there are two stainless...
I have a 78 XL100 i had running last season. I had the engine out this winter to put new valve seals in etc. and have recently put the engine back on the bike to fire it up for the season. I noticed it had spark at first but then suddenly no spark. I decided to check for power from the...
Any prefered brand ?
a bit out of touch with who make quality product these days.
front end is coming out as i have a slight weep on one leg and the headrace is a little notchy.
got new koyo bearings and motul syntetic 10w oil just need some seals now.
quite like the look of these...
So, last time I had the carb apart I put in a 55 slow jet
As it turns out or seems atm a 55 is a little too much.
Seems to run ok but tickover still a bit erratic
Anyway, see if you can answer this
If I leave it ticking over and then switch off the fuel, it seems to smooth out and the tickover...
I am thinking of maybe getting replacement exhausts / silencers, mine are standard
If you have replaced your Dominator exhausts, I would love to find out all about them
Please could you answer these questions to help me decide
What is the make of your replacements ?
How much were they in...
Later in the year I will be rebuilding my front forks with progressive springs, in respect of the seals do I need to order one of these kits:
2 Oil Seals
2 Dust Seals
2 Retaining Clips
2 Inner Bushes
2 Outer Bushes
Or can I just order the seals?
Also what fork oil...
I have a selection of new bearings left over that are no longer of use to me: -
91071-KS6-004 x4 Swing Arm Needle Bearing
52141-MM9-000 x2 Swing Arm Bearing
52473-MS8-000 x2 Rear shock linkage Bearing
52144-KR8-005 x2 Swing Arm Dust Seals
91254-KS6-003 x1 Dust Seal
52109-MM9-300 x2 Swing...
I'm Marco from Belgium. I have an RD04 from 1990. It's a great bike, but has had some bad owners that didn't maintain it. :(
I have replaced the rubber inlet seals, valve cover seals, fuel hoses, blablabla... =)
Now i am left with one part: a screw, a tiny washer and something on...
Anyone had an issue with these All Balls Fork Dust Seals?
Fork Oil seals fitted ok. The retaining clip is seated...
i'm planning to replace the piston rings , valve seals and sort the head along with replacing the timing chain set on my dommie.
My question is , can all of that be done while the engine is in the frame??
I’m restoring my RD03, I have just taking the entire bike apart and will start with the frame and engine.
The engine was burning about 1L oil for 2,500km and most of the seals are leaking so I will replace all the seals and put some new piston rings in.
My question to ye is what...