settings

Does anyone know the correct torque settings for the front and rear sprocket nuts?

So just bought it its silver/black 2005 abs 22k on it,i have fitted a new front tyre(metzler tourance) have bought a new chain and sprockets and my question is,does anyone know the correct torque settings for the front sprocket and the nuts for the rear sprocket,i live in londonderry n.ireland...

It wont let me change my email address in "settings" It doesn't email me when I get a private message It doesn't email me when there is a reply to a thread I am subscribed to All this seems to have started a few days ago Is anyone else having these problems?

To improve starting, I'd like to take the carb back to the original (UK) settings. I have a manual showing Main Jet 142 and Slow Jet 52. However, the manual appears to be for USA models. Would UK models have been fitted with the same jets?

To improve starting, I'd like to take the carb back to the original (UK) settings. I have a manual showing Main Jet 142 and Slow Jet 52. However, the manual appears to be for USA models. Would UK models have been fitted with the same jets?

Hi. Dose Any one have a workshop manual that can tell me the base carb settings. Float hights And fuel mixture screw settings Many thanks Sent from my SM-G955F using Tapatalk

Have a newly acquired 2008 700. Does anyone know the factory settings for damping and preload on a std shock? Its fine over big bumps (like speed humps) but a small, frequent sequence (like when the tarmac gets ripples in it - or rumble strips) feels like there's no suspension at all. I'm...

Does anyone have the torque settings for the bottom linkage bolts, below rear shocker, for the above, please. All I can find in my workshop manual is ' tighten the bolts securely '. ??

I'm about to tighten the nuts holding the exhaust down pipe to the cylinder head on my 2002 RD07A. My Haynes manual tells me that the torque setting should be 27nm (or 20 lbft), which strikes me as a bit high considering that I've just done the same job on my CB1300 and the torque setting there...

I am currently restoring a 1980 xl185 and have managed to get a voltage at the input to the coil. I have connected my multimeter to the spade connector from the CDI and the needle bounces about to a maximum of 5v when the bike is kicked over. I guess this is what I should be seeing? I have no...

Any one know what the torque settings are for the rear brake disk? I put a new chain and sprockets, cush drive and rear disk on the bike the other week and getting some weird things happening, grabbing at low speed, and having trouble getting it right and have the mot next week so its belt and...

This is now on the terrace. There is fuel in the tank but the battery only lasted about a minute but at least we got a backfire. The battery is now on charge. Do I need to alter the standard carb settings after putting bigger jets in for the free flowing carb It started after a bit of faffing...

Hi fitted New jets in standard Kevin carb think it's running a bit lean could do with some info float height and needle valve clip position thanks

Purchased my new ride the other day, an 07 Varadero 1000. This will be my fourth!!! Very pleased with it, but I do not remember the ride being so firm. It's only done 19000 miles, one owner with full service. The rear is harsh. Smooth undulating roads, no problem. A bit more than that and it...

Hi guys, I'm new to this site and was wondering if anybody may be able to help???? My 2005 xr125 is leaking oil from the head gasket, I have bought a new top end gasket set. But before I start to strip it down I wanted to find the torque settings for the head bolts, rocker shaft etc... I can't...

Hi guys, I'm new to this site and was wondering if anybody may be able to help???? My 2005 xr125 is leaking oil from the head gasket, I have bought a new top end gasket set. But before I start to strip it down I wanted to find the torque settings for the head bolts, rocker shaft etc... I can't...

Hi , I've just fitted an ignitech controller to my fmx 650 and was wondering if any body has any good advance settings for these units thanks Neil

Evenin' all, I'm clued up on the 'legalities' of flashing lights etc. but I've come across an interesting situ today and looking for some clarafication if anyone can help? I've purchased some small LED cycling lamps for a couple of the pushirons in the garage, they have various settings that...

I am looking to buy an exhaust stystem for my 94 Dominator to cut down on weight. :rolleyes: I would like something that I can bolt straight on without having to fiddle with the carb settings. I wouldnt be against something that might piss my neighbours off :D:D:D Your advice would be...

hi, just got my xr 400 back together after being sat for 6 months without an engine and the rear suspension is really jumpy on the return, when i accelerate its like being on a rocking horse the back end is all over the place, i see the cylinder on the side of the shock has a valve and ive tried...