Search Results for ‘slr’

Does anyone have any experience removing or replacing the steel sleeve and rubber bushings in the fork top bridge where the stems of the 2 handlebar lower holders fit in? The stems are secured by a 14mm nut underneath the bridge. On my Vigor, the handlebar lower holders have developed a lot of...

I've started to get a rapid rattling/buzz coming from the insider the clutch cover on start-up. It goes away after about 10 seconds. I took off the clutch cover expecting a loose tab washer on the clutch - but that's fine. I notice that the oil pump driven gear can be rattled a bit, though...

Does anyone have any experience removing the right-side footrest hanger from an FX650 (same parts - I think - as the SLR)? I'm trying to get the clutch cover off to check the strainer mesh in the oil pipe and the footrest hanger needs to come off first. I'm using the SLR manual as there isn't...

Hi please let me know if any of you have one of these for sale-thanks

Hey all After about 3 years, I'm about to kick off the build of my SLR650 scrambler/tracker. I'm looking to get a 17" front wheel & am looking at fitting a 120/70/17 up front with 150/70/17 rear Continental TKC80's. Now after some research, I'm not sure if these will fit on the current wheel...

heres my slr/fmx ive not been on here for a while just fired the bike up today its been stood for 2 years.

I’m pretty sure all the above use the same basic frame, so the dimensions i’m after should be the same. Could someone with a Swing-Arm from one of these measure the front pivot width. That would be the outer width, i.e. the width required in the frame and also the inside width, i.e. the width...

Gents, just a quick one; I have an SLR650 with Continental Twinduro TKC 80 multi use tyres. F - 110/80 19 R - 120/90 17 whats the best pressures? I know the manual says 22/22psi but its too low. Nothing on Continental website specifically to say what pressures although couple of interesting...

Hi there;couple of things (1) I'm changing the fork oil in my 99 FX650 Vigor. The tech data gives the quantity and level but no recommendation for the grade of oil. The bike is only used on the street, so any suggestions please? (2) Bit of a long shot this, but would anybody have an actual...

got an SLR 650 with no carb any condition considered as i will clean and rebuild. also looking to put a 21" wheel and brake in it swap for the current 19" set up ?? cheers Ewen. located in London .

hi, I've got a problem with my great condition, low milage (11,000) SLR 650 and hope that someone might be able to help. I bought it in August and everything has been working faultlessly until I went to start it last week and it sounded like the battery was going flat which was strange because...

I have owned this bike for the past 3 years and has been 100% reliable. It was first registered in Dec 1998 and is MOT'd until 16 Aug 2019. It is fantastic condition for its age and has a full service history with receipts to back this up. The bike was garaged for many years and recommissioned...

'98 SLR 650, mileage is 78,000 but has had a ground up rebuild over last winter, asking £1800

does anyone know if the slr bashplate would fit the fx650y?

I am looking for a set of crash bars for my 2001 FX650 Vigor. Is the frame different to a SLR frame. Does the Dominator have the same frame. There seems to a number of different model numbers starting with RD 0?. Does anyone know what the model number is for the Vigor. Just acquired the Vigor...

Anyone recommend some decent brake discs for and RD08 that dont break the bank Running the standard dommie rear wheel with an SLR650 front wheel. Looking on evilbay, prices range from £30 to £130 for a disc??

Hi Folks, Would anyone happen to have a spare front wheel spindle they would like to off load? My Dommi one has a slight bend to it. I believe the FX and SLR (and some other honda models) has the same spindle. Thanks Jim

Hi, folks, this is a two-parter part 1 i am in need of a front calliper for my new dommie project has anyone got one for sale or trade? part 2 is there a choice of calipers i can work with? i had a slr front caliper on one of my dommies , is there a further choice that you know of? i seem to...

Set to with the debaffle today. Cut the end off the two baffles so I could get 38mm hole saw in. Cut the baffle out and then welded a 42mm piece of pipe onto the hole so it looks a bit tidier. Gave it all a blast with some black vht paint and she sounds like a good un. Just got to swap the main...

Gents, Im sure this has been done before; can you give me sign posting to instructions for fuel tank removal (and/or workshop manual) as want to send it away to Dream Machine for Rothmans paint job :) thanks kimosabby