Being a vertically challenged 5’7 90kg with 30” inside leg I might need to lower my (new to me)Xr400r a tad!
ive bought a second hand seat and will be sending it off to get the foam shaved down a bit and a new seat cover but think it might not be enough!
Was considering a lowering link but it...
This is a long shot but I figured I would give it a shot. I have a 1996 transalp in the blue/navy colour combo.
I have badly damaged my front cowl and offside front side panel.
Would anyone happen to have any fairings in this colour combo that they can sell?
If not I will have to suck...
Just wondering whether anyone knows of a suitable source for replacement barrel lock for my Honda Topbox on my Transalp XL700?
The one on at the moment is getting more and more fiddly to open every day and is only a matter of time before it refuses to open.
The OE replacement lock set is Honda...
I'm in Utah USA and need engine parts for my RD07
Can anyone suggest a parts source in the US or someone in UK / EU that ships to the US? References good or bad would be appreciated.
Anyone who can suggest a good shop to do valve work on the heads here in the US would also be appreciated...
Anyone know where or if I can pick up a fuel pump connector plug? I would like to have the facet pump I bought to have as a spare on my next road trip and just put a stock plug on it to have ready. I have a set of new points to put in old pump and would like to keep it in place for now. I really...
Im new the forum and require urgent help.
I need to source a crankshaft for my XRV750 as far as I know the RD04 and the RD07 uses the same Crank is this correct.
For some unknown reason mine broke 3 teeth on the Timing Gear.
Im leaving a a long distance tour in 3 weeks and just my...
Has anyone out there got an un-wanted centre stand for a 600 Alp (mines a '98 model, but earlier ones should fit)?
Checked with that excellent source of new Honda parts, David Silvers, and apparently the stand is no longer available.
The after market availability of a stand is very patchy as...
Having trouble with a weak spark on my Honda XL250R. We think the source coil is at fault but on test it gives 76 Ohms resistance. The correct resistance is unclear as the manual we have says reading should be in the range 200 to 500 Ohms. However later it says that for post 1981 the reading the...
Does anyone know the dimensions or numbers of front and rear bearings and seals ?
I want to put some in my spares box before a trip and can normally source them through work :)
List from lings site to help future readers
My Rear wheel of my 88 RD03 has serious rim rot and the bike won't get through an MOT. I've been trying to source a new rear wheel but had no luck. I have found a rear wheel from a 1998 model and wondering if it would fit? Thought I'd ask hear for advice.
My other route is to get a...
I was lucky enough to source a slightly used Boano tank.
The fasteners that were on the tank do not have the smaller "inner" piece that accepts the twist stud.
Can anyone tell me if the Boano kit comes with these or does one drill out the riveted pieces on the OEM tank and use?
Managed to source some KTM 950/990 front Brembo calipers with brake lines
So thinking of a better m/c. Know that a 2003 CBR600RR one fits but has anyone fitted a radial one?
See that on the evil bay you can get generic 7/8" bar Chinese brake and clutch radials but wondered if anyone has fitted...
I need a new o-ring for my fuel petcock. Rather than order an original honda part which will take a couple days to me (and possibly bug the honda place where I just picked up what I actually needed via another order), I was just going to source a generic o-ring for this tomorrow, then I can...
This time last year I asked about fitting an oil cooler on my Dommie but got side tracked as I was having clutch and flatside issues and lack of funds to finance an oil cooler.
Anyhoo ,the clutch was replaced and now works as it should and my flatside is dialled in now with the help of our...