Honda XRV Forum banner

spindle

  1. Front Wheel Spindle/Axle - Help

    Dominator / FMX
    Hi Folks, Would anyone happen to have a spare front wheel spindle they would like to off load? My Dommi one has a slight bend to it. I believe the FX and SLR (and some other honda models) has the same spindle. Thanks Jim
  2. Tansalp XL600VV forks

    Transalp
    I have damaged the left hand fork slider (bottom at the thread where the spindle screws in). I can get second hand ones from ebay but they are from the single disk model. Now, the single disk model has the disk on the l/h/s, good, I obviously need the mounts for the calliper, but are they the...
  3. XR Front wheels?

    XR
    Is the XR250 (96-2004) front wheel the same spindle size and fit as the XR400 one Can anyone confirm?
  4. XR400 ~ XR650 Front Wheel

    XR
    A bit of a long shot...does anyone know if an XR650 front wheel will fit a 2004 XR400R? My XR has had a different front wheel fitted to the XR forks and still retains the XR spindle & speedo drive etc Cheers Gary
  5. Front spindle clamp.

    Africa Twin
    Right, here's one of those that doesnt crop up too often. Decided to stick with the Honda forks so having a service, new seals, oil, springs, Intiminators , shot blast & new enamel. But one of the four fork studs are snapped & Mr Honda doesn't give a part number anyone had to change one??
  6. Where to put CHT sensor

    Dominator / FMX
    Trying to get some ideas for the best place to put a washer type cht sensor. I thought about bolting it to the hole where the spindle for the unused decomp lever normally goes or maybe the little threaded hole above it. Any one else using one and where did you attach it Could you also submerge...
  7. XL fork question...

    XL
    Hi all, I am building a special and have picked up what I believe to be some XL600 forks (gold sliders if that makes any difference) The thread in the fork leg is a metric fine M12x1.25 and I'm after a spindle to suit. The ones I've seen for sale seem to be M14x1.5 thread. Can anybody shed any...
  8. xr 250 spindle !!

    XR
    good morning all, i have what i belive to be a 1982 xr250 in a box or box,s !!!, the rear spindle was missing so found one on ebay unfortunatly the spindel is to short for the swing arm and the diamiter of the spindel is also to small for the wheel barings could this be an earlyer model or a...
  9. Torque settings

    Transalp
    Hi, does anyone have the torque settings for the following on a XL650V-6; Steering stem nut Fork yolk bolts Brake caliper bolts Front wheel spindle clamp nuts and anything else on the front end that I've forgotten :D cheers, Bob.
  10. XL250 forks - have I wasted my money?

    XL
    Hi folks My next project is a XL250 S-B, on which the forks have more pit than chrome.....so I bought some XL forks off e bay only to find that they are earlier and have a different spindle mount - SB's have the 4 bolt version from the XR's. So, does anyone know if these use the same spindle...
  11. special tools needed for swing arm?

    Dominator / FMX
    hola, re-greasing the swing arm bearings and possible fitting a grease nipple ( why isnt there one as standard?) is next on my list. i have heard some hondas have pre-loaded bearings needing a special tool to remove. does a dominator have that or just old school bearings and spindle. thank you.
  12. spindle

    Transalp
    can anybody confirm spindle dimensions for ta 650. spindle 17mm with fat end dia 22mm and 230mm long. if this is correct its the same size as xr 600 92 onwards,xr 400 and xr650r. anbody got one for sale?
  13. Rear wheel spindle

    Transalp
    Evening all I have recently become the proud owner of a 1988 600V TA in excellent condition and am really pleased with it except ... I was going to adjust the chain as it was a little bit slack. After reading the owner's manual and with the bike on the side stand, I stupidly started to slacken...
  14. Help! Rear Wheel Spindle Size XR125-L5

    XR
    Help, I have bu99ered up the thread on the rear wheel spindle on my XR125 2005. Anyone know what size diameter it is for when I go to buy a tapping kit in the morning, - don't have anything accurate to measure it with :( Cheers
  15. wheel spindle sizes?

    XR
    For the xr400 - anyone know? Ta
  16. XR Spindle sizes?

    XR
    I will shortly be putting my 'left over' wheels for sale on Ebay after selling my xr250r to 'mauser'. I need help to confiirm which models i can state that they will fit. They appear to have 14mm ID bearings on the front wheel and 17mm ID bearings on the rear wheel. They were used on my...
  17. XR 250: Oil Leak and Play around kick starter spindle?

    XR
    I have a 98 xr 250. I just recently noticed that there is a bit of oil and dirt around the kick start spindle. With a little closer inspection I noticed that there is a little play in the spindle as well. I'm guesing that the seal around the spindle is bad? Has anyone attempted to solve this...
  18. Xr spindle size?

    XR
    Quick question Am I right in thinking the XR600R has a 17 mm wheel spindle?
  19. Rear wheel spindle

    Transalp
    Hi, I have just replaced the rear tyre, and in checking the microfiche the spindle on my bike was the opposite way around with the nut on the chain side. Does this matter? Cheers
  20. Chain Adjustment Spindle Cams

    Africa Twin
    Does anybody know where i can buy a new pair of cams for the chain adjustment? The numbers on mine are hardly visible so wheel alignment is a bit tricky. cheers Ralph
Top