Honda XRV Forum banner

splined

  1. For Sale / Wanted
    Anyone got a good/new splined gear lever for an nx650? If so please send details, cheers Nige.
  2. Transalp
    Dammit my worst fears about buying one of these has come true :mad::mad::mad: Should have removed the front sprocket when I bought the bike.. ARGHH Ok so I have read a bit about this the only true solution is to strip the engine and replace but just how big a job is that? is it a complete...
  3. XR
    Hello, Can anyone tell me if my final drive oil seal, the splined drive coming out of the gearbox where the front sprocket is mounted -- can be replaced from the outside or do i have to open up the gearbox? Thanks y'all... Rossa in west cork.
  4. XR
    Is the later 13 spline transmission countershaft a direct replacement for a 1988 xr600 or do I have to replace it with the early 6 splined version. I only ask because when I look for then on supplier sites the early ones are listed as discontinued. Does anyone on here know of a new one or am I...
  5. XR
    Hi all I was cleaning my newly aquired XR250 today, after a weekend trail ride, and noticed the kickstart seemed to have come adrift and was about to fall off, however, when I checked it, it was correctly fitted and fully tightened up. I'm not sure why, but it seems like it's 'hanging off'...
  6. Africa Twin
    Has abdee kept the worn output shaft? I would like to have a look at what is left of a bad one,I have a few ideas buzzing around in my head,one of which is to make a splined sleeve to use what is left . Happy to pay the postage if someone would like to donate a scrapper to my research--...
  7. Africa Twin
    During the recent strip/re-spray job I discovered the reason for a wierd rattle type noise in second gear - the splines on the mainshaft have worn. The sprokect has been sitting too far outboard due to a very worn retaining plate on a pattern sprocket. :( I've managed to 'fix' it by putting 2...
  8. Dominator / FMX
    Hi there, anyone else had a problem with the gear selector foot lever coming loose on the splined shaft. The splines on the shaft and foot lever do not appear to be excessivly worn, but I,m sure they will if I keep having to tap it back on and re tighten, thread lock or some other engineering...
  9. Africa Twin
    Sadly I have the soft output drive which means my front sprocket has a real bad wobble...now I don,t know how long it will last before stripping the splines off the shaft alltogether but I,m thinking of using another sprocket with the teeth cut off and welded onto the the new sprocket...
  10. Dominator / FMX
    Hello everyone. Anyone got any tips to remove the gear shift lever? The pinch bolt had sheared, I have managed to remove the thread that was left in the lever using pliers; however, when trying to remove the lever from the splined shaft it only comes off the shaft about a 1/4 of an inch and...
  11. Africa Twin
    Just to reasure me..... Servicing the bike this weekend I noticed a little bit of slack in the drive sprocket..... the teeth and chain all look fine.... the slack was in the splined shaft union with the sprocket... is this normal? or should it be replaced... especially before I set off for the...
  12. Africa Twin
    So I,m waiting on my mate turning up for a road ride and have put the africa in the garage and readied the blackbird ,started looking at the oil leak from the left hand side of the africa so whip the gear lever and cover off for a closer look and fiddle a bit only to find massive play on...
  13. Africa Twin
    Hello from another new AT guy. I've just got my first AT (RD07) with the intention of going traveling (at some point!) on it. As i'm new to the bike, I decided to give it a service and general check. The first thing that i noticed was that the rear shock had the spring wound to the "max...
Top