Honda XRV Forum banner

torque

  1. CRF1000L Service Manual

    Africa Twin
    My CRF1000L is now out of warranty so kicking dealer servicing into touch :p Having just clocked 16000 miles a valve check was due (££££££££). So I reviewed the Honda Service Manual - pretty poor, watched some YouTube videos and then came across a fantastic service manual from Marks Motorcycle...
  2. Slip-On Mufflers by Akrapovic for Honda CRF at MOTORCYCLEiD.com

    MOTORCYCLEiD
    The Akrapovic company, with its technologically advanced manufacturing facilities and highly-skilled specialists, is considered a pioneer in its field. The company was founded in 1991 by Igor Akrapovič, a racer who was pursuing perfection but couldn’t find suitable products for his bike on the...
  3. Torque settings for sprockets

    Varadero Technical Specs
    Does anyone know the correct torque settings for the front and rear sprocket nuts?
  4. Proud new owner XL1000 V5

    Varadero
    So just bought it its silver/black 2005 abs 22k on it,i have fitted a new front tyre(metzler tourance) have bought a new chain and sprockets and my question is,does anyone know the correct torque settings for the front sprocket and the nuts for the rear sprocket,i live in londonderry n.ireland...
  5. Headstock Reassembly XRV750 RD04?

    Africa Twin
    Hi Fellow XRV enthusiasts. Most of you are probably on your bike today as glorious weather but hopefully someone around to ask:) Replaced Headstock bearings on my RD04 (AT) and failed to make sufficient notes for reassembly. If anyone has a reassembly diagram then grateful, if not then good...
  6. FMX 650 valve clearance

    Dominator / FMX
    Hi to all, I would like to ask what the recommended valve clearances for FMX 650 are. My net research gave me two outcomes: (1) 0.10 (intake) and 0.12 (exhaust) +-0.02 (like in XR650L, Dominator etc) , and (2) 0.10 +-0.02 for both intake and exhaust valves (see here...
  7. Torque settings for 2002 fx650y

    Dominator / FMX
    does anyone know or tell me where i could find the correct torque settings,the ones i need are as follows,the oil filter housing bolts,sump bung bolts(on frame and at the bottem),rear wheel axle,front wheel station,fork yokes and also the two allen key bolts on the head the ones that would be...
  8. NX650 Oil Strainer Removal

    Dominator / FMX
    Anyone taken the oil strainer out of the bottom of their frame? Tried removing it yesterday, so i could check it, and get frame ready for powder coat, but could not get it to undo. Tried interlocking two spanners to get a higher torque, but still no joy. Any tips on removal???
  9. Honda CB750A Hondamatic-an adventure bike-perhaps

    Other Honda
    I have got the CB750A sorted and have done a few miles on it now the weather has improved. Its different, obviously with the 2 speed and torque converter transmission, most definitely not a racer, but they are used for drag racing in US slightly, VERY modified! Great for bumbling along the...
  10. Design Fault with Front wheel Axle Holder

    Transalp
    Was doing a routine check and found that the front axle holder was broken and the nuts on the studs were so loose that they could come off by hand. Anyway as I do not have torque wrench I managed to snap 1 stud off and then was trying to put a temporary support plate which caused the other stud...
  11. Where have all the big trail bikes gone?

    Other Bikes
    I was at the NEC for Motorcycle Live this week, and whilst the pages of the motorcycling press are plastered with "Adventure Bikes", it was noticeable that there weren't any big trail bikes at the show. If you want to spend £20k on 125+bhp and 250kg of touring bike on long travel suspension then...
  12. Torque settings for XRV 2001 Africa twin

    Africa Twin Technical Specs
    Does anyone have the torque settings for the bottom linkage bolts, below rear shocker, for the above, please. All I can find in my workshop manual is ' tighten the bolts securely '. ??
  13. Rd07a exhaust downpipe nut torque settings

    Africa Twin
    I'm about to tighten the nuts holding the exhaust down pipe to the cylinder head on my 2002 RD07A. My Haynes manual tells me that the torque setting should be 27nm (or 20 lbft), which strikes me as a bit high considering that I've just done the same job on my CB1300 and the torque setting there...
  14. Whats it worth?

    Chatter
    I found an imperial measurements socket set for sale here in Denmark for £20 Its make is USAG which I have never heard of and its has 21 sockets from 3/8" up to ! 1/4" which is a bargain in this part of Europe that I call home.. While I was talking to the seller I asked if he had any other tools...
  15. my '95 Dommie clean up!

    Dominator / FMX
    So after a number of months sitting in spare parts in my garage, the ol' Dommie is finally back together! Cleaned her up from the frame up, stuck a Wiseco high compression piston in the motor, fresh tyres, braided front brake line, repainted a few bits such as exhausts, fork top tee, handlebars...
  16. Clutch bolts torque question

    Dominator / FMX
    Hi guys 1) Does anyone knows torque value for the 4 bolts in clutch plate? https://image.slidesharecdn.com/hondanx-650dominatorservicemanual-121214134812-phpapp01/95/honda-nx-650-dominator-service-manual-112-638.jpg?cb=135549S and torque value for bolt to oil strainer screen(right crankcase)...
  17. Torque talk.

    Chatter
    Its that time of year again when my thoughts turn to servicing my bikes for spring.:cool::cool::cool: I need to get my hands on a decent torque wrench because my head needs seeing to.:D:D:D I have only done a couple of hundred miles on my Dommie since I fitted a Wiseco piston and replaced my...
  18. 1983 xr350 kickstarter

    XR
    Hi all I recently bought a 1983 HONDA Xr350 in pieces. I'm slowly getting things back together. My question is right now I am trying to figure out how the kickstart shaft goes in. The shop manual says to set it by rotating the shaft counterclockwise but the pictures show it rotate clockwise so...
  19. Running woes. Cdi issues?

    Transalp
    Xl600v 1990. Tick over perfect. Open throttle perfect. Whilst riding it's like it's bogging down tops out at 60 eventually no torque. Fuel lines fine, carbs spotless, jets clear. My exhaust is shite but this hasn't changed and it did run perfect? Im not in the position to fork out...
  20. Transalp 650 voltage / charging / RR

    Transalp
    Hello, I recently changed my air filter, and went for a ride. It made a big difference - better sound and more low down torque. On this ride, I stopped for some fish and chips. Went to start my bike and the box next to the battery (relay?) made a clicking noise, but no power to the bike. I...
Top