Honda XRV Forum banner

xr650l

  1. Hi guys, what is sprockets tooths numbers on an FMX

    Dominator / FMX
    I bought a XR650R (thicker) 15T front sprocket, then I found out that on my FMX front sprocket is 14T. Which is original? 14T or 15T? BTW I found on the INTERNET that people are fitting XR650R front sprocket on XR650L to prevent it from cutting into sprocket splines. Please note that XR650L and...
  2. Parts Sharing?

    Dominator / FMX
    Does the '88 NX650 I just bought share many -- or any -- parts with other models like the XL600 or XR650L?
  3. For Sale: Xr650l Anyone

    For Sale / Wanted
    This is just down the road from me nice looking bike but too much money for me https://www.ebay.co.uk/itm/Honda-XR-XR650L-XR600-XL-Paris-Dakar/383057137161?hash=item592ffc0e09:g:pewAAOSwTs5dI25B
  4. Wanted: XR650L Wiring Harness

    Bikes For Sale / Wanted
    Does anyone have a wiring loom from a XR650L for sale? Condition not important as it will likely be modified anyway so the cheaper the better, I'm just looking for a decent starting point.
  5. High compression piston for Dominator?

    Dominator / FMX
    I'm hoping to build a special dominator motor with a high compression piston - say 10.5:1 No problem I thought, as Wiseco do them for the XR650L - which is the same as the Dominator right? Does anyone know 100% for sure if this is true of all XR650L motors because the Wiseco catalogue does not...
  6. XR650L oil pump into an RD08 dommie?

    Dominator / FMX
    Hey chaps, I've just obtained an XR650L oil pump (15100-MY6-670) I understood this to be a worthwhile upgrade from the standard NX5650 oil pump But it doesn't seem to fit. Help! Update: It does fit following some minor mods outlined later on in this thread.
  7. FMX 650 valve clearance

    Dominator / FMX
    Hi to all, I would like to ask what the recommended valve clearances for FMX 650 are. My net research gave me two outcomes: (1) 0.10 (intake) and 0.12 (exhaust) +-0.02 (like in XR650L, Dominator etc) , and (2) 0.10 +-0.02 for both intake and exhaust valves (see here...
  8. Help with trying to adjust the Mikuni TM40 on my bike

    XR
    Hi All, I've just recently aquired an 93' XR650L and it didn't run well initially. Symptoms where popping once in a while while driving, but also when standing still, dropping gas to idle, it ran for around 15 secs and then one pop in the exhaust and boom stop :-) I reckoned it was running to...
  9. Wanted: XR650L or XR600R Header Pipes

    For Sale / Wanted
    Hi all, does anyone have a set of header pipes laying around they would like to sell? Please let me know. Sent from my LG-D855 using Tapatalk
  10. Wanted: Flywheel wanted

    For Sale / Wanted
    Anyone got a spare flywheel with the ring gear etc that they want to sell ? It's for my fmx but dominator or xr650l will fit too, so I'm lead to believe. Cheers
  11. Flywheel wanted

    Dominator / FMX
    Anyone got a spare flywheel with the ring gear etc that they want to sell ? It's for my fmx but dominator or xr650l will fit too, so I'm lead to believe. Cheers DB
  12. Piston replacement

    Dominator / FMX
    Hi all. Just picked up a FMX 650 that’s had a replacement engine. It came with the old engine that’s got a shagged piston but apart from that it’s in good shape. I’m looking to buy a new piston and rebuild the old engine. My question is can I use the same diameter 100mm piston from the XR650L...
  13. Top Yoke Options

    Dominator / FMX
    Morning All, Has anyone had a go at fitting just a top yoke from any of the Honda family? I'm wondering if an XR600 or an XR650L may fit the dommi? I know the ignition switch could be an issue but its more does it fit the forks and stem ok? Reason I ask is I am trying to find a yoke with...
  14. Turn signal lens different pre/post 1990?

    Transalp
    Hi, I'm looking to replace the amber lens on my 1992 Transalp for clear or smoke glass. I found these but it says it fits only models up to 1990. Is there really a difference pre/post 1990? I thought they were the same until 1993.
  15. Washable oil filter - anyone?

    Dominator / FMX
    Hello. I have being lately doing some maintenance to my dominator and in this opportunity is time for the oil filter. I was browsing online that there are some washable oil filter, basically a oil filter that you could clean and reuse like the k&n air filter, made from stainless steel...
  16. Valve clearances, you have clearance Clarence.

    Dominator / FMX
    Hi Guys, I think I am going to check my valve clearances tomorrow. No real reason, bike seems to be fine as is but think I should check them. Not been done since I have owned the bike. So what do I need? I have new o-rings for the big nut cover things and a socket which fits a...
  17. Wanted: Wanted ! Rockers or complete Rocker Cover for NX 650 , XR650L , XR600 .

    For Sale / Wanted
    Hi All , As per the header - I need to replace the Rockers on a '03 Dominator, I've looked at E-Bay and most of the stuff is in the States , would prefer to buy from nearer home . Has any body got the Rockers or a complete Rocker Cover to sell or know of one at reasonable money ? Thanks in...
  18. Wanted: Africa twin or xr650l

    Bikes For Sale / Wanted
    Hello there. I am new to this site as a member however have been flicking through this site on and off over recent years. I am in the market for a new bike but torn and don't really mind either an Africa twin or a thumper XR650L. I'm not sure what I would prefer of the two and yes well aware...
  19. An XR650L I built.

    XR
    I've bought a few of these now and have been bringing them back to 'better than new' standard. They're such a rare bike here and such a bloody fantastic bike too. Why we never got them here is a mystery. They're still produced and sell well in USA, Aus and South Africa. Unchanged since 1993...
  20. A Dommie I built...

    Dominator / FMX
    One I knocked up earlier in the year. This was my own bike so kind of just played around with it making it how I liked myself. Not scared to crash it either. It came off roading with me a few times. I had a Hagon with stiffer springs so it handled quite well. I've done a couple of XR650L's...
Top